ADUC7122BBCZ-RL Analog Devices Inc, ADUC7122BBCZ-RL Datasheet - Page 39
![PRECISION ANALOG MCU I.C](/photos/6/69/66991/bc-108-2_sml.jpg)
ADUC7122BBCZ-RL
Manufacturer Part Number
ADUC7122BBCZ-RL
Description
PRECISION ANALOG MCU I.C
Manufacturer
Analog Devices Inc
Series
MicroConverter® ADuC7xxxr
Datasheet
1.ADUC7122BBCZ.pdf
(96 pages)
Specifications of ADUC7122BBCZ-RL
Core Processor
ARM7
Core Size
16/32-Bit
Speed
41.78MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
32
Program Memory Size
126KB (63K x 16)
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 3.6 V
Data Converters
A/D 13x12b, D/A 12x12b
Oscillator Type
Internal
Operating Temperature
-10°C ~ 95°C
Package / Case
108-LFBGA, CSPBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ADUC7122BBCZ-RL
ADUC7122BBCZ-RLTR
ADUC7122BBCZ-RLTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADUC7122BBCZ-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Table 54. FEExSTA MMR Bit Designations
Bit
15:6
5
4
3
2
1
0
Table 55. FEExMOD MMR Bit Designations
Bit
7:5
4
3
2
1:0
Table 56. Command Codes in FEExCON
Code
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
1
The FEExCON register always reads 0x07 immediately after execution of any of these commands.
1
1
1
1
1
1
1
Description
Reserved.
Reserved.
Reserved.
Flash/EE interrupt status bit.
Set automatically when an interrupt occurs, that is, when a command is complete and the Flash/EE interrupt enable bit in the
FEExMOD register is set.
Cleared when reading the FEExSTA register.
Flash/EE controller busy.
Set automatically when the controller is busy.
Cleared automatically when the controller is not busy.
Command fail.
Set automatically when a command completes unsuccessfully.
Cleared automatically when reading the FEExSTA register.
Command complete.
Set by ADuC7122 when a command is complete.
Cleared automatically when reading the FEExSTA register.
Description
Reserved. Always set these bits to 0 except when writing Flash memory control keys.
Flash/EE interrupt enable.
Set by the user to enable the Flash/EE interrupt. The interrupt occurs when a command is complete.
Cleared by user to disable the Flash/EE interrupt.
Erase/write command protection.
Set by the user to enable the erase and write commands.
Cleared to protect the Flash/EE memory against erase/write command.
Reserved. Should always be set to 0 by the user.
Flash/EE wait states. Both Flash/EE blocks must have the same wait state value for any change to take effect.
Command
Null
Single read
Single write
Erase/write
Single verify
Single erase
Mass erase
Reserved
Reserved
Reserved
Reserved
Signature
Protect
Reserved
Reserved
Ping
Description
Idle state.
Load FEExDAT with the 16-bit data indexed by FEExADR.
Write FEExDAT at the address pointed by FEExADR. This operation takes 50 μs.
Erase the page indexed by FEExADR and write FEExDAT at the location pointed by FEExADR. This operation
takes 20 ms.
Compare the contents of the location pointed by FEExADR to the data in FEExDAT. The result of the comparison
is returned in FEExSTA Bit 1.
Erase the page indexed by FEExADR.
Erase user space. The 2 kB of kernel are protected in Block 0. This operation takes 2.48 sec. To prevent accidental
execution, a command sequence is required to execute this instruction.
Reserved.
Reserved.
Reserved.
Reserved.
Gives a signature of the 64 kB of Flash/EE in the 24-bit FEExSIGN MMR. This operation takes 32,778 clock cycles.
This command can be run only once. The value of FEExPRO is saved and can be removed only with a mass erase
(0x06) or with the key.
Reserved.
Reserved.
No operation, interrupt generated.
Rev. 0 | Page 39 of 96
ADuC7122