ADUC7061BCPZ32-RL Analog Devices Inc, ADUC7061BCPZ32-RL Datasheet - Page 70

• Manufacturer Part Number: ADUC7061BCPZ32-RL
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7061BCPZ32-RL

• Design Resources: USB Based Temperature Monitor Using ADuC7061 and an External RTD (CN0075) 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuC7060/ADuC7061
TIMER2 OR WATCHDOG TIMER
Timer2 has two modes of operation, normal mode and
watchdog mode. The watchdog timer is used to recover
from an illegal software state. When enabled, it requires
periodic servicing to prevent it from forcing a reset of the
processor.
Timer2 reloads the value from T2LD either when Timer2
overflows or immediately when T2CLRI is written.
Normal Mode
Timer2 in normal mode is identical to Timer0 in the 16-bit
mode of operation, except for the clock source. The clock
source is the low power, 32.768 kHz oscillator scalable by a
factor of 1, 16, or 256.
Watchdog Mode
Watchdog mode is entered by setting T2CON[Bit 5]. Timer2
decrements from the timeout value present in the T2LD register
until zero. The maximum timeout is 512 seconds, using a
maximum prescaler/256 and full scale in T2LD.
User software should not configure a timeout period of less
than 30 ms. This is to avoid any conflict with Flash/EE memory
page erase cycles that require 20 ms to complete a single page
erase cycle and kernel execution.
If T2VAL reaches 0, a reset or an interrupt occurs, depending
on T2CON[1]. To avoid a reset or an interrupt event, any value
must be written to T2CLRI before T2VAL reaches zero. This
reloads the counter with T2LD and begins a new timeout period.
When watchdog mode is entered, T2LD and T2CON are
write protected. These two registers cannot be modified until
a power-on reset event resets the watchdog timer. After any
other reset event, the watchdog timer continues to count. To
avoid an infinite loop of watchdog resets, configure the
watchdog timer in the initial lines of user code. User software
should configure a minimum timeout period of 30 ms only.
Timer2 halts automatically during JTAG debug access and only
recommences counting after JTAG relinquishes control of the
ARM7 core. By default, Timer2 continues to count during
power-down. To disable this, set Bit 0 in T2CON. It is
recommended that the default value be used, that is, that the
watchdog timer continues to count during power-down.
32.768kHz
PRESCALER
1, 16, 256
Figure 25. Timer2 Block Diagram
Rev. B | Page 70 of 108
UP/DOWN COUNTER
16-BIT LOAD
TIMER2
VALUE
16-BIT
Timer2 Interface
The Timer2 interface consists of four MMRs.
•
•
•
Timer2 Load Register
Name:
Address:
Default value:
Access:
Function:
Timer2 Clear Register
Name:
Address:
Access:
Function:
Timer2 Value Register
Name:
Address:
Default value:
Access:
Function:
T2CON is the configuration MMR, described in (Table 81).
T2LD and T2VAL are 16-bit registers (Bit 0 to Bit 15) and
hold 16-bit, unsigned integers. T2VAL is read only.
T2CLRI is an 8-bit register. Writing any value to this
register clears the Timer2 interrupt in normal mode or
resets a new timeout period in watchdog mode.
WATCHDOG RESET
TIMER2 IRQ
T2LD
0xFFFF0360
0x0040
Read and write
This 16-bit MMR holds the Timer2
reload value.
T2CLRI
0xFFFF036C
Write only
This 8-bit, write-only MMR is written (with
any value) by user code to refresh (reload)
Timer2 in watchdog mode to prevent a
watchdog timer reset event.
T2VAL
0xFFFF0364
0x0040
Read only
This 16-bit, read-only MMR holds the
current Timer2 count value.