HSDL-3000#007 Lite-On Electronics, HSDL-3000#007 Datasheet - Page 2

• Manufacturer Part Number: HSDL-3000#007
• Description: Infrared Transceivers IR Transceiver 115.2Kb/s
• Manufacturer: Lite-On Electronics

Specifications of HSDL-3000#007

• Wavelength: 875 nm
• Continual Data Transmission: 115.2 Kbit/s
• Transmission Distance: 1.5 m
• Radiant Intensity: 75 mW/sr
• Half Intensity Angle Degrees: 30 deg to 60 deg
• Pulse Width: 7.5 us, 1.6 us
• Maximum Rise Time: 100 ns, 600 ns
• Maximum Fall Time: 100 ns, 600 ns
• Led Supply Voltage: 0 V to 7 V
• Operating Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 20 C
• Dimensions: 9.1 mm x 3.65 mm x 2.7 mm
• Data Rate: 115.2kbs (SIR)
• Idle Current, Typ @ 25° C: 0.02µA
• Link Range, Low Power: 1.5m
• Operating Temperature: -20°C ~ 70°C
• Orientation: Side View
• Shutdown: *
• Size: 9.1mm x 3.65mm x 2.7mm
• Standards: IrPHY 1.3
• Supply Voltage: 2.7 V ~ 5.5 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

I/O Pins Configuration Table
Pin
1
2
3
4
5
6
–
Recommended Application Circuit Components
Component
R1
2.7 Ω ± 5%, 0.25 Watt, for 3.0 ≤ V
Watt, for 4.5 ≤ V
CX1
CX2
Notes:
1. CX1 must be placed within 0.7 cm of HSDL-3000 to obtain optimum noise immunity.
2. In environments with noisy power supplies, supply rejection can be enhanced by including CX2 as shown in ”HSDL-3000
2
Functional Block Diagram
Functional Block Diagram“on page 2.
[1]
[2]
Caution: The BiCMOS inherent to the design of this component increases the component’s susceptibility to
damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken during han-
dling and assembly of this component to prevent damage and/or degradation, which may be induced by ESD.
Symbol
LED A
TXD
RXD
SD
V
GND
SHIELD
CC
CC
≤ 5.5 V operation
Description
LED Anode
Transmitter Data Input.
Active High.
Receiver Data Output.
Active Low.
Shutdown.
Active High.
Supply Voltage
Ground
EMI Shield
RXD (3)
TXD (2)
Recommended Value
2.2 Ω ± 5%, 0.25 Watt, for 2.7 ≤ V
0.47 µF ± 20%, X7R Ceramic
6.8 µF ± 20%, Tantalum
SD (4)
CC
≤ 3.6 V operation
HSDL-3xxx
V
CC
TRANSMITTER
R1
(5)
CX2
CX1
LEDA (1)
V
Notes
Tied through external resistor, R1, to regulated V
Logic High turns on the LED. If held high longer than ~ 50 µs, the LED is turned
off. TXD must be either driven high or low. Do NOT float the pin.
Output is a low pulse response when a light pulse is seen.
Complete shutdown TXD, RXD, and PIN diode.
Regulated, 2.7 to 5.5 volts.
Connect to system ground.
Connect to system ground via a low inductance trace.
For best performance, do not connect to GND directly at the part.
CC
CC
≤ 3.3 V operation
GND (6)
SHIELD
6.8 Ω ± 5%, 0.25
Pinout
6
CC
from 2.7 to 5.5 volts.
5
Marking Information
The HSDL-3000#007/017 is marked
with a number “0” and “YWWLL” on
the shield where ‘Y’ indicates the
unit’s manufacturing year, ‘WW’
refers to the work week and ‘LL’ is
the lot information.
REAR VIEW
4
3
2
1