MFRC52302HN1,151 NXP Semiconductors, MFRC52302HN1,151 Datasheet - Page 62

• Manufacturer Part Number: MFRC52302HN1,151
• Description: IC READER 32-HVQFN
• Manufacturer: NXP Semiconductors
• Series: MIFARE®r

Specifications of MFRC52302HN1,151

• Rf Type: Read / Write
• Frequency: 13.56MHz
• Features: ISO14443-A, ISO14443-B
• Package / Case: 32-VFQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935293911151

NXP Semiconductors
MFRC523
Product data sheet
COMPANY PUBLIC
9.2.4.3 TestSel2Reg register
9.2.4.4 TestPinEnReg register
General test signal configuration and PRBS control.
Table 122. TestSel2Reg register (address 32h); reset value: 00h bit allocation
Table 123. TestSel2Reg register bit descriptions
Enables the test bus pin output driver.
Table 124. TestPinEnReg register (address 33h); reset value: 80h bit allocation
Table 125. TestPinEnReg register bit descriptions
Bit
Symbol
Access
Bit
7
6
5
4 to 0 TestBusSel[4:0]
Bit
Symbol
Access
Bit
7
6 to 1 TestPinEn[5:0]
0
Symbol
TstBusFlip
PRBS9
PRBS15
Symbol
RS232LineEn
reserved
RS232LineEn
TstBusFlip
R/W
R/W
7
7
All information provided in this document is subject to legal disclaimers.
Rev. 3.7 — 8 November 2011
Value Description
0
-
-
PRBS9
Value Description
1
-
-
-
R/W
6
6
serial UART lines MX and DTRQ are disabled
enables the output driver on one of the data pins D1 to D7 which
outputs a test signal
Example:
Remark: If the SPI is used, only pins D1 to D4 can be used. If the
serial UART interface is used and the RS232LineEn bit is set to
logic 1 only pins D1 to D4 can be used.
reserved for future use
115237
test bus is mapped to the parallel port in the following order:
TstBusBit4,TstBusBit3, TstBusBit2, TstBusBit6, TstBusBit5,
TstBusBit0; see
starts and enables the PRBS9 sequence according to
ITU-TO150; the data transmission of the defined sequence is
started by the Transmit command
Remark: all relevant registers to transmit data must be
configured before entering PRBS9 mode
starts and enables the PRBS15 sequence according to
ITU-TO150; the data transmission of the defined sequence is
started by the Transmit command
Remark: all relevant registers to transmit data must be
configured before entering PRBS15 mode
selects the test bus; see
setting bit 1 to logic 1 enables pin D1 output
setting bit 5 to logic 1 enables pin D5 output
PRBS15
R/W
5
5
TestPinEn[5:0]
4
Section 16.1 on page 80
4
R/W
Section 16.1 “Test signals” on page 80
3
3
TestBusSel[4:0]
R/W
2
2
Contactless reader IC
MFRC523
© NXP B.V. 2011. All rights reserved.
1
1
reserved
62 of 98
0
0
-