ATTINY861-20PU Atmel, ATTINY861-20PU Datasheet - Page 79

• Manufacturer Part Number: ATTINY861-20PU
• Description: Microcontrollers (MCU) 8kB Flash 0.512kB EEPROM 16 I/O Pins
• Manufacturer: Atmel

Specifications of ATTINY861-20PU

• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire/SPI/USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRMC320
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Package / Case: PDIP-20
• Controller Family/series: AVR Tiny
• Core Size: 8 Bit
• No. Of I/o's: 16
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Ram Size: 512 Byte
• Operating Temperature: -40 to 85 °C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.7.4
11.7.5
11.8
2588E–AVR–08/10
Timer/Counter Timing Diagrams
8-bit Input Capture Mode
16-bit Input Capture Mode
cases to consider in the Normal mode, a new counter value can be written anytime. The Output
Compare Unit can be used to generate interrupts at some given time.
The Timer/Counter0 can also be used in an 8-bit Input Capture mode, see
77
The Timer/Counter0 can also be used in a 16-bit Input Capture mode, see
77
The Timer/Counter is a synchronous design and the timer clock (clk
clock enable signal in the following figures. The figures include information on when Interrupt
Flags are set.
shows the count sequence close to the MAX value.
Figure 11-7. Timer/Counter Timing Diagram, no Prescaling
Figure 11-8
Figure 11-8. Timer/Counter Timing Diagram, with Prescaler (f
Figure 11-9 on page 80
TCNTn
(clk
TCNTn
(clk
TOVn
TOVn
clk
clk
clk
clk
for bit settings. For full description, see the section
for bit settings. For full description, see the section
I/O
I/O
I/O
Tn
I/O
Tn
/1)
/8)
shows the same timing data, but with the prescaler enabled.
Figure 11-7
MAX - 1
MAX - 1
shows the setting of OCF0A and OCF0B in Normal mode.
contains timing data for basic Timer/Counter operation. The figure
MAX
MAX
“Input Capture Unit” on page
“Input Capture Unit” on page
clk_I/O
BOTTOM
BOTTOM
/8)
T0
) is therefore shown as a
Table 11-3 on page
Table 11-3 on page
BOTTOM + 1
BOTTOM + 1
75.
75.
79