XBP24-DMWIT-250 Digi International, XBP24-DMWIT-250 Datasheet - Page 54

• Manufacturer Part Number: XBP24-DMWIT-250
• Description: XBEE-PRO MESH 2.4 EXTENDED
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP24-DMWIT-250

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 18dBm
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 250mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Whip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q4542387

XBee/XBee‐PRO DigiMesh 2.4 RF Modules
Appendix B: Agency Certifications
United States (FCC)
OEM Labeling Requirements
FCC Notices
FCC-Approved Antennas (2.4 GHz)
XBee/XBee-PRO DigiMesh 2.4 RF Modules comply with Part 15 of the FCC rules and regulations.
Compliance with the labeling requirements, FCC notices and antenna usage guidelines is required.
To fulfill FCC Certification requirements, the OEM must comply with the following regulations:
Required FCC Label for OEM products containing the XBee/XBee‐PRO DigiMesh 2.4 RF Module
* The FCC ID for the XBee is “OUR‐XBEE”. The FCC ID for the XBee‐PRO is “OUR‐XBEEPRO”.
IMPORTANT: The XBee/XBee-PRO DigiMesh 2.4 OEM RF Module has been certified by the FCC
for use with other products without any further certification (as per FCC section 2.1091). Modifica-
tions not expressly approved by Digi could void the user's authority to operate the equipment.
IMPORTANT: OEMs must test final product to comply with unintentional radiators (FCC section
15.107 & 15.109) before declaring compliance of their final product to Part 15 of the FCC Rules.
IMPORTANT: The RF module has been certified for remote and base radio applications. If the
module will be used for portable applications, the device must undergo SAR testing.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures: Re-orient or relocate the receiving antenna,
increase the separation between the equipment and receiver, connect equipment and receiver to
outlets on different circuits, or consult the dealer or an experienced radio/TV technician for help.
XBee/XBee-PRO RF Modules can be installed using antennas and cables constructed with standard
connectors (Type-N, SMA, TNC, etc.) if the installation is performed professionally and according
to FCC guidelines. For installations not performed by a professional, non-standard connectors
(RPSMA, RPTNC, etc) must be used.
Contains FCC ID: OUR-XBEE/OUR-XBEEPRO*
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any inter-
ference received, including interference that may cause undesired operation.
1.
2.
© 2010 Digi International, Inc.
The system integrator must ensure that the text on the external label provided with this
device is placed on the outside of the final product [Figure A-01].
XBee/XBee-PRO DigiMesh 2.4 RF Modules may only be used with antennas that have been
tested and approved for use with this module [refer to the antenna tables in this section].
WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling
requirements are met. This includes a clearly visible label on the outside of the final
product enclosure that displays the contents shown in the figure below.
54