XBP24-DMWIT-250 Digi International, XBP24-DMWIT-250 Datasheet - Page 32

• Manufacturer Part Number: XBP24-DMWIT-250
• Description: XBEE-PRO MESH 2.4 EXTENDED
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP24-DMWIT-250

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 18dBm
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 250mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Whip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q4542387

5. DigiMesh 2.4 Command Reference Tables
XBee/XBee‐PRO DigiMesh 2.4 RF Modules
Special
AT
Command
WR
RE
FR
AC
VL
AT
Command
DH
DL
DD
SH
SL
HP
SE
DE
CI
NP
AT
Command
AP
AO
Addressing
Serial Interfacing (I/O)
Special Commands
Addressing Commands
Serial Interfacing Commands
Name and Description
Write. Write parameter values to non-volatile memory so that parameter modifications
persist through subsequent resets.
Note: Once WR is issued, no additional characters should be sent to the module until
after the "OK\r" response is received.
Restore Defaults. Restore module parameters to factory defaults.
Software Reset. Reset module. Responds immediately with an “OK” then performs a
reset 100ms later.
Apply Changes. Immediately applies new settings without exiting command mode.
Version Long. Shows detailed version information including application build date and
time.
Name and Description
Destination Address High. Set/Get the upper 32 bits of the 64-bit destination address.
When combined with DL, it defines the destination address used for transmission.
Destination Address Low. Set/Get the lower 32 bits of the 64-bit destination address.
When combined with DH, DL defines the destination address used for transmission.
Device Type Identifier. Stores a device type value. This value can be used to
differentiate multiple XBee-based products.
Serial Number High. Read high 32 bits of the RF module's unique IEEE 64-bit
address. 64-bit source address is always enabled. This value is read-only and it never
changes
Serial Number Low. Read low 32 bits of the RF module's unique IEEE 64-bit address.
64-bit source address is always enabled. This is read only and it is also the serial
number of the node..
Hopping Channel.
Set/read the spread spectrum channel on which the module communicates. Separate
channels minimize interference between multiple networks operating in the same
vicinity.
Source Endpoint. Set/read the application layer source endpoint value. This value will
be used as the source endpoint for all data transmissions. The default value 0xE8 (Data
endpoint) is the Digi data endpoint
Destination Endpoint.
Set/read application layer destination ID value. This value will be used as the
destination endpoint for all data transmissions. The default value (0xE8) is the Digi data
endpoint.
Cluster Identifier.
Set/read application layer cluster ID value. This value will be used as the cluster ID for
all data transmissions. The default value 0x11 (Transparent data cluster ID)
Maximum RF Payload Bytes.
This value returns the maximum number of RF payload bytes that can be sent in a
unicast transmission based on the current configurations.
Name and Description
API mode. Set or read the API mode of the radio. The following settings are allowed:
0 API mode is off. All UART input and output is raw data and packets are delineated
using the RO parameter.
1 API mode is on. All UART input and output data is packetized in the API format,
without escape sequences.
2 API mode is on with escaped sequences inserted to allow for control characters
(XON, XOFF, escape, and the 0x7e delimiter to be passed as data.
API Output Format. Enables different API output frames. Options include:
0 Standard Data Frames (0x90 for RF rx)
1 Explicit Addressing Data Frames (0x91 for RF rx)
© 2010 Digi International, Inc.
Parameter Range
--
--
--
--
--
Parameter Range
0 to 0xFFFFFFFF
0 to 0xFFFFFFFF
0-0xFFFFFFFF
[ read only ]
0-0xFFFFFFFF
0-0xFFFFFFFF
0-0x7 (standard variant)
0-0x3 (International
variant)
0-0xFF
0-0xFF
0-0xFFFF
0-0xFFFF
Parameter Range
0, 1, or 2
0, 1
Default
--
--
--
--
--
Default
0
0x0000FFFF
0x40000
Factory
Factory
0
0xE8
0xE8
0x11
n/a
Default
0
0
32