XBP24-DMWIT-250 Digi International, XBP24-DMWIT-250 Datasheet - Page 38

• Manufacturer Part Number: XBP24-DMWIT-250
• Description: XBEE-PRO MESH 2.4 EXTENDED
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP24-DMWIT-250

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 18dBm
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 250mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Whip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q4542387

XBee/XBee‐PRO DigiMesh 2.4 RF Modules
AT
Command
ID
NT
NI
DN
ND
NO
AT
Command
SM
SO
Node Identification
Node Identification Commands
Sleep Commands
Name and Description
PAN ID. Set or read the user network address. Nodes must have the same network
address to communicate. Changes to ID should be written to non-volatile memory using
the WR command.
Node Discover Timeout. Set/Read the amount of time a node will spend discovering
other nodes when ND or DN is issued.
Node Identifier. Stores a string identifier. The string accepts only printable ASCII data
In AT Command Mode, the string can not start with a space. A Carriage return ends the
command. Command will automatically end when maximum bytes for the string have
been entered. This string is returned as part of the ATND (Network Discover) command.
This identifier is also used with the ATDN (Destination Node) command. .
Discover Node - Destination Node. Resolves an NI (Node Identifier) string to a
physical address (casesensitive).
The following events occur after the destination node is discovered:
(Node Identifier) string.
The 64-bit extended addresses is returned in an API Command Response frame.
If there is no response from a module within (NT * 100) milliseconds or a parameter is
not specified (left blank), the command is terminated and an “ERROR” message is
returned. In the case of an ERROR, Command Mode is not exited.
Node Discover - Node Discover. Discovers and reports all RF modules found. The
following information is reported for each module discovered.
After (NT * 100) milliseconds, the command ends by returning a <CR>. ND also accepts
a Node Identifier (NI) as a parameter (optional). In this case, only a module that
matches the supplied identifier will respond. If ND is sent through the API, each
response is returned as a separate AT_CMD_Response packet. The data consists of
the above listed bytes without the carriage return delimiters. The NI string will end in a
"0x00" null character.
Network Discovery Options.
Set/Read the options value for the network discovery command. The options bitfield
value can change the behavior of the ND (network discovery) command and/or change
what optional values are returned in any received ND responses or API node
identification frames.
Options include:
0x01 = Append DD value (to ND responses or API node identification frames)
0x02 = Local device sends ND response frame when ND is issued.
Name and Description
Sleep Mode.
Set/read the sleep mode of the module.
Sleep Options.
Options Include:
bit 0 = Preferred Sleep Coordinator
bit 1 = Non-Sleep Coordinator
bit 2 = Enable API sleep status messages
bit 3 = Disable automatic early wakeup for missed syncs
bit 4 = SM7 and SM8 nodes are considered equal for purposes of election
bit 5 = Disable coordinator rapid sync deployment mode.
1. DL & DH are set to the extended (64-bit) address of the module with the matching NI
<AT Firmware>
2. OK (or ERROR)\r is returned.
3. Command Mode is exited to allow immediate communication
<API Firmware>
0xFFFE<CR>
SH<CR>
SL<CR>
NI<CR> (Variable length)
PARENT_NETWORK ADDRESS (2 Bytes)<CR>
DEVICE_TYPE<CR> (1 Byte: 0=Coord, 1=Router, 2=End Device)
STATUS<CR> (1 Byte: Reserved)
PROFILE_ID<CR> (2 Bytes)
MANUFACTURER_ID<CR> (2 Bytes)
<CR>
© 2010 Digi International, Inc.
Parameter Range
0x0000 to 0x7FFF
0x2EE0
[x 100 msec]
up to 20 byte ASCII string a space character
20 byte ascii string
0-0x03 [bitfield]
Parameter Range
0 (Normal)
7 (Sleep Support Node)
8 (Cyclic Sleep)
0-0xFF
(bits 0 and 1 cannot be
both set at the same time)
Default
0x7FFF
0x82 (130d)
0
Default
0
0
38