XBP24-DMWIT-250 Digi International, XBP24-DMWIT-250 Datasheet - Page 35

• Manufacturer Part Number: XBP24-DMWIT-250
• Description: XBEE-PRO MESH 2.4 EXTENDED
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP24-DMWIT-250

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: ISM
• Applications: General Purpose
• Power - Output: 18dBm
• Sensitivity: -100dBm
• Voltage - Supply: 2.8 V ~ 3.4 V
• Current - Receiving: 55mA
• Current - Transmitting: 250mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Wire Whip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: Q4542387

XBee/XBee‐PRO DigiMesh 2.4 RF Modules
AT
Command
D5
D8
D9
RP
PR
M0
M1
LT
CB
IR
IF
I/O Commands
Name and Description
AD5/DIO5 Configuration.
Select/Read function
DIO8 Configuration.
Select/Read function for the DIO8 line of the RF module.
DIO9 Configuration.
Select/Read function for the DIO9 line of the RF module.
RSSI PWM Timer.
Time RSSI signal will be output after last transmission. When RP = 0xFF, output will
always be on.
Pullup Resistor Configuration.
Set/read the bit field that configures the internal pull-up resistor status for the I/O lines.
"1" specifies the pull-up resistor is enabled. "0" specifies no pullup.
Bits:
0 - DIO4/AD4 (Pin 11)
1 - AD3 / DIO3 (Pin 17)
2 - AD2 / DIO2 (Pin 18)
3 - AD1 / DIO1 (Pin 19)
4 - AD0 / DIO0 (Pin 20)
5 - RTS / DIO6 (Pin 16)
6 - DTR / SLEEP_RQ/DI08 / DIO8 (Pin 9)
7 - DIN / Config (Pin 3)
8 - Associate / DIO5 (Pin 15)
9 - On/Sleep / DIO9 (Pin 13)
10 - DIO12 (Pin 4)
11 - PWM0 / RSSI / DIO10 (Pin 6)
12 - PWM1 / DIO11 (Pin 7)
13 - DIO7/CTS (Pin 12)
14 - DOUT (Pin 2)
PWM0 Output Level
Set/Read the PWM0 output level.
PWM1 Output Level
Set/Read the PWM1 output level.
Assoc LED Blink Time.
Set/Read the Associate LED blink time. If the Associate LED functionality is enabled
(D5 command), this value determines the on and off blink times for the LED when the
module has joined a network. If LT=0, the default blink rate will be used (500ms sleep
coordinator, 250ms otherwise). For all other LT values, LT is measured in 10ms.
Commissioning Pushbutton.
This command can be used to simulate commissioning button presses in software. The
parameter value should be set to the number of button presses to be simulated. For
example, sending the ATCB1 command will execute the action associated with 1
commissioning button press. (See D0 command).
IO Sample Rate.
Set/Read the IO sample rate to enable periodic sampling. For periodic sampling to be
enabled, IR must be set to a non-zero value, and at least one module pin must have
analog or digital IO functionality enabled (see D0-D9, P0-P2 commands). The sample
rate is measured in milliseconds.
Sample from Sleep Rate.
Set/read the number of sleep cycles that must elapse between periodic IO samples.
This allows IO samples to be taken only during some wake cycles. During those cycles
IO samples are taken at the rate specified by IR.
© 2010 Digi International, Inc.
Parameter Range
0 - Disabled
1 - Associated indication
LED
2 - Analog input, single
ended
3 - Digital input, monitored
4 - Digital output, default
low
5 - Digital output, default
high
0 – Disabled
3 - Digital input, monitored
4 - Digital output, default
low
5 - Digital output, default
high
0 – Disabled
1 – ON_SLEEP line
3 - Digital input, monitored
4 - Digital output, default
low
5 - Digital output, default
high
0 - 0xFF [x 100 ms]
0 - 0x1FFF
0x3FF
0x3FF
0x14 - 0xFF (200 - 2550
ms)
-
0 - 0xFFFF (ms)
1-0xFF
Default
1
0
1
0x28 (4 sec.)
0x1FFF
0
0
0
-
0
1
35