SI1013-A-GM Silicon Laboratories Inc, SI1013-A-GM Datasheet - Page 314

• Manufacturer Part Number: SI1013-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1013-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1870-5

Si1010/1/2/3/4/5
Table 24.5. SMBus Status Decoding With Hardware ACK Generation Disabled (EHACK = 0)
314
Values Read
1110
1100
1000 1 0 X A master data byte was
0 0 X A master START was gener-
0 0 0 A master data or address byte
0 0 1 A master data or address byte
Current SMbus State
ated.
was transmitted; NACK
received.
was transmitted; ACK
received.
received; ACK requested.
Rev. 1.0
Typical Response Options
Load slave address + R/W into
SMB0DAT.
Set STA to restart transfer.
Abort transfer.
Load next data byte into
SMB0DAT.
End transfer with STOP.
End transfer with STOP and start
another transfer.
Send repeated START.
Switch to Master Receiver Mode
(clear SI without writing new data
to SMB0DAT).
Acknowledge received byte;
Read SMB0DAT.
Send NACK to indicate last byte,
and send STOP.
Send NACK to indicate last byte,
and send STOP followed by
START.
Send ACK followed by repeated
START.
Send NACK to indicate last byte,
and send repeated START.
Send ACK and switch to Master
Transmitter Mode (write to
SMB0DAT before clearing SI).
Send NACK and switch to Mas-
ter Transmitter Mode (write to
SMB0DAT before clearing SI).
Write
0 0 X 1100
1 0 X 1110
0 1 X -
0 0 X 1100
0 1 X -
1 1 X -
1 0 X 1110
0 0 X 1000
0 0 1 1000
0 1 0 -
1 1 0 1110
1 0 1 1110
1 0 0 1110
0 0 1 1100
0 0 0 1100
Values to