SI1013-A-GM Silicon Laboratories Inc, SI1013-A-GM Datasheet - Page 20

• Manufacturer Part Number: SI1013-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1013-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 13dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 30mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 13 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1870-5

Si1010/1/2/3/4/5
1. System Overview
Si1010/1/2/3/4/5 devices are fully integrated mixed-signal System-on-a-Chip MCUs. Highlighted features
are listed below. Refer to Table 2.1 for specific product feature selection and part ordering numbers.















With on-chip Power-On Reset, V
devices are truly stand-alone System-on-a-Chip solutions. The Flash memory can be reprogrammed even
in-circuit, providing non-volatile data storage, and also allowing field upgrades of the 8051 firmware. User
software has complete control of all peripherals, and may individually shut down any or all peripherals for
power savings.
The on-chip Silicon Labs 2-Wire (C2) Development Interface allows non-intrusive (uses no on-chip
resources), full speed, in-circuit debugging using the production MCU installed in the final application. This
debug logic supports inspection and modification of memory and registers, setting breakpoints, single
stepping, run and halt commands. All analog and digital peripherals are fully functional while debugging
using C2. The two C2 interface pins can be shared with user functions, allowing in-system debugging with-
out occupying package pins.
Each device is specified for 0.9 to 1.8 V, 0.9 to 3.6 V or 1.8 to 3.6 V operation over the industrial tempera-
ture range (–40 to +85 °C). The Port I/O and RST pins are tolerant of input signals up to 5 V. The
Si1010/1/2/3/4/5 devices are available in a 42-pin QFN package which is lead-free and RoHS compliant.
See Table 2.1 for ordering information. Block diagrams are included in Figure 1.1 through Figure 1.4.
The transceiver's extremely low receive sensitivity (–121 dBm) coupled with industry leading +20 dBm out-
put power ensures extended range and improved link performance. Built-in antenna diversity and support
for frequency hopping can be used to further extend range and enhance performance. The advanced radio
features including continuous frequency coverage from 240–960 MHz in 156 Hz or 312 Hz steps allow pre-
cise tuning control. Additional system features such as an automatic wake-up timer, low battery detector,
64 byte TX/RX FIFOs, automatic packet handling, and preamble detection reduce overall current con-
sumption. The transceivers digital receive architecture features a high-performance ADC and DSP-based
modem which performs demodulation, filtering, and packet handling for increased flexibility and perfor-
mance. The direct digital transmit modulation and automatic PA power ramping ensure precise transmit
modulation and reduced spectral spreading, ensuring compliance with global regulations including FCC,
ETSI, ARIB, and 802.15.4d regulations. An easy-to-use calculator is provided to quickly configure the radio
settings, simplifying customer's system design and reducing time to market.
20
240–960 MHz EZRadioPRO
Single/Dual Battery operation with on-chip dc-dc boost converter.
High-speed pipelined 8051-compatible microcontroller core (up to 25 MIPS)
In-system, full-speed, non-intrusive debug interface (on-chip)
10-bit 300 ksps or 12-bit 75 ksps single-ended ADC with analog multiplexer
6-Bit Programmable Current Reference. Resolution can be increased with PWM.
Precision programmable 24.5 MHz internal oscillator with spread spectrum technology.
16 kB or 8 kB of on-chip Flash memory
768 bytes of on-chip RAM
SMBus/I
Four general-purpose 16-bit timers
Programmable Counter/Timer Array (PCA) with six capture/compare modules and Watchdog Timer
function
On-chip Power-On Reset, V
Two On-chip Voltage Comparators with 11 Capacitive Touch Sense inputs.
15 Port I/O (5 V tolerant except for GPIO_0, GPIO_1, and GPIO_2)
2
C, Enhanced UART, and two Enhanced SPI serial interfaces implemented in hardware
DD
®
transceiver
DD
Monitor, and Temperature Sensor
monitor, Watchdog Timer, and clock oscillator, the Si1010/1/2/3/4/5
Rev. 1.0