XR88C681J-F Exar Corporation, XR88C681J-F Datasheet - Page 4

• Manufacturer Part Number: XR88C681J-F
• Description: IC UART CMOS DUAL 44PLCC
• Manufacturer: Exar Corporation
• Type: CMOS Dual Channel UARTr

Specifications of XR88C681J-F

• Number Of Channels: 2, DUART
• Package / Case: 44-LCC (J-Lead)
• Features: *
• Fifo's: 1 Byte, 3 Byte
• Voltage - Supply: 5V
• With Parallel Port: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current: 15 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• Propagation Delay Time Ns: 400 ns
• No. Of Channels: 2
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: PLCC
• No. Of Pins: 44
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1329

PIN DESCRIPTION
44 PLCC
Rev. 2.11
10
12
13
11
1
2
3
4
5
6
7
8
9
40 PDIP,
CDIP
10
11
1
2
3
4
5
6
7
8
9
28 PDIP
1
2
3
4
5
6
7
8
(RXCA - Z)
(TXCA - I)
Symbol
(-CTSB)
(-CTSA)
RXDB
TXDB
-WR
-RD
NC
IP3
IP1
IP0
NC
A0
A1
A2
A3
Type
O
I
I
I
I
I
I
I
I
I
I
4
Description
No Connection.
LSB of Address Input. This input, along with Address Inputs,
A1 - A3 are used to select certain registers within the DUART
device, during READ and WRITE operations with the CPU.
Input Port 3. General Purpose Input - When the DUART is
operating in the I-mode, this input can also be used as the
external clock input for the Channel A Transmitter (TXCA).
When the DUART is operating in the Z-Mode, this input can
be used as the external clock input for the Channel A Receiv-
er (RXCA).
Address Input.
Input Port 1. General Purpose Input - This input can also be
used as the Active Low, “Channel B Clear to Send” input.
(
Address Input.
MSB of Address Input. This input, along with Address In-
puts, A0 - A2 are used to select certain registers within the
DUART device, during READ and WRITE operations with the
CPU.
Input 0. General Purpose Input - This input can also be used
as the active-low, “Channel A Clear-to-Send” input. (-CTSA)
Write Strobe (Active-Low). A “low” on this input while -CS is
also “low” writes the contents of the Data Bus into the ad-
dressed register, within the DUART. The transfer occurs on
the rising edge of -WR.
Read Strobe (Active Low). A “low” on this input while
also “low” places the contents of the addressed DUART regis-
ter, on the data bus.
Receive Serial Data Input (Channel B). The least significant
bit of the character is received first. If external receiver clock,
RXCB, is specified, the data is sampled on the rising edge of
this clock.
No Connect.
Transmitter Serial Data Output (Channel B). The least sig-
nificant bit of the character is transmitted first. This output is
held in the high (marking state) when the transmitter is idle,
disabled, or when the channel is operating in the local LOOP-
BACK mode. If an external transmitter clock is specified,
TXCB, the transmitted data is shifted out of the TSR (Trans-
mitter Shift Register) on the falling the edge of this clock.
-
CTSB)
-
CS is