AT91SAM7S256C-MU Atmel, AT91SAM7S256C-MU Datasheet - Page 504

• Manufacturer Part Number: AT91SAM7S256C-MU
• Description: IC ARM7 MCU 32BIT 256K 64-QFN
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S256C-MU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• Processor Series: AT91
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: SPI, TWI, USART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 5
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT91SAM7S256-MU; AT91SAM7S256-MU

35.5.2
35.5.2.1
504
AT91SAM7S Series Preliminary
Handling Transactions with USB V2.0 Device Peripheral
Setup Transaction
Figure 35-4. Control Read and Write Sequences
Notes:
Setup is a special type of host-to-device transaction used during control transfers. Control trans-
fers must be performed using endpoints with no ping-pong attributes. A setup transaction needs
to be handled as soon as possible by the firmware. It is used to transmit requests from the host
to the device. These requests are then handled by the USB device and may require more argu-
ments. The arguments are sent to the device by a Data OUT transaction which follows the setup
transaction. These requests may also return data. The data is carried out to the host by the next
Data IN transaction which follows the setup transaction. A status transaction ends the control
transfer.
When a setup transfer is received by the USB endpoint:
Thus, firmware must detect the RXSETUP polling the UDP_ CSRx or catching an interrupt, read
the setup packet in the FIFO, then clear the RXSETUP. RXSETUP cannot be cleared before the
setup packet has been read in the FIFO. Otherwise, the USB device would accept the next Data
OUT transfer and overwrite the setup packet in the FIFO.
• The USB device automatically acknowledges the setup packet
• RXSETUP is set in the UDP_ CSRx register
• An endpoint interrupt is generated while the RXSETUP is not cleared. This interrupt is
carried out to the microcontroller if interrupts are enabled for this endpoint.
Control Read
Control Write
No Data
Control
1. During the Status IN stage, the host waits for a zero length packet (Data IN transaction with no
2. During the Status OUT stage, the host emits a zero length packet to the device (Data OUT
data) from the device using DATA1 PID. Refer to Chapter 8 of the Universal Serial Bus Specifi-
cation, Rev. 2.0, for more information on the protocol layer.
transaction with no data).
Setup Stage
Setup Stage
Setup Stage
Setup TX
Setup TX
Setup TX
Status Stage
Status IN TX
Data OUT TX
Data IN TX
Data Stage
Data Stage
Data OUT TX
Data IN TX
6175K–ATARM–30-Aug-10
Status OUT TX
Status Stage
Status IN TX
Status Stage