MPC5553MZQ132 Freescale Semiconductor, MPC5553MZQ132 Datasheet - Page 63

• Manufacturer Part Number: MPC5553MZQ132
• Description: IC MCU MPC5553 REV A 324-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC55xx Qorivvar

Specifications of MPC5553MZQ132

• Core Processor: e200z6
• Core Size: 32-Bit
• Speed: 132MHz
• Connectivity: CAN, EBI/EMI, Ethernet, SCI, SPI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 220
• Program Memory Size: 1.5MB (1.5M x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.35 V ~ 1.65 V
• Data Converters: A/D 40x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 324-PBGA
• Processor Series: MPC5xxx
• Core: e200z6
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: 7-Wire, DSPI, ESCI
• Maximum Clock Frequency: 132 MHz
• Number Of Timers: 56
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: MPC5553EVBISYS - KIT EVAL ISYSTEMS MPC5553MPC5553EVBGHS - KIT EVAL GREEN HILLS SOFTWAREMPC5553EVB - KIT EVAL MPC5553MZP132MPC5553EVBE - BOARD EVAL FOR MPC5553
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

Freescale Semiconductor
Table 7
Table 8
Table 9
Location
Power Sequence Pin Status for Fast Pads
Power Sequence Pin Status for Medium/Slow Pads:
DC Electrical Specifications:
• Changed title to Pin Status for Fast Pads During the Power Sequence
• Changed preceding paragraph
• Changed title to Pin Status for Medium and Slow Pads During the Power Sequence
• Updated preceding paragraph.
• Spelled the slash ‘/’ as ‘and’ as well as ‘I/O’ as ‘input/output.’ Still very confusing. Deleted ‘input/output’.
• Added footnote that reads: V
• Spec 20, column 2, Characteristics,’ Slow and medium output high voltage (I
• Spec 20, column 4, Min.: Added a blank line before and after ‘0.80 × V
• Spec 22, column 2, ’Slow and medium output low voltage (I
• Spec 26: Changed ‘AN[12]_MA[1]_SDO’ to ‘AN[13]_MA[1]_SDO’.
• Spec 27a: Operating current 1.5 V supplies @ 132 MHz changed to:
• Spec 27b, Operating current 1.5 V supplies @ 114 MHz changed to:
• Spec 27c, Operating current 1.5 V supplies @ 82 MHz changed to:
• Spec 28: Changed 132 MHz to f
• Footnote 3 changed to read: If standby operation is not required, connect V
• Footnote 6 is now:
• Deleted footnote 9: ‘Preliminary. Final specification pending characterization.’
• Deleted duplicate footnote: ‘ Absolute value of current, measured at V
a range of 1.6–3.6 V if EBTS =1.
Created a left-justified second line and moved ‘I
the parentheses. Created a left-justified third line that reads ‘I
line.
and moved ‘I
left-justified third line that reads ‘I
V
values.
spikes, etc., the state of the I/O pins during power up/down varies depending on power. Prior to exiting POR, the
pads are in a high impedance state (Hi-Z).
To:
spikes, and so on. Therefore, the state of the I/O pins during power up/down varies depending on which supplies
are powered.
From:
Although there are no power up/down sequencing requirements to prevent issues like latch-up, excessive current
There are no power up/down sequencing requirements to prevent issues such as latch-up, excessive current
DDEH
1.65 typical = 460
1.35 typical = 360
1.65 high = 510
1.35 high = 410
1.65 typical = 410
1.35 typical = 310
1.65 high = 460
1.35 high = 370
1.65 typical = 330
1.35 typical = 225
1.65 high = 385
1.35 high = 290
Table 33. Table and Figure Changes Between Rev. 2.0 and 3.0 (continued)
’ and put ‘0.15 × V
OL_S
= 2.0 mA.’ from the 1st line to the second line and deleted the parentheses. Created a
Figure 3
MPC5553 Microcontroller Data Sheet, Rev. 3.0
DDEH
shows an illustration of the IDD_STBY values interpolated for these temperature
DDE2
’ on the last line.
MAX
OL_S
and V
MHz.
= 1.0 mA.’ Column 5, Max: Added a blank line before and after ‘0.20 ×
DDE3
Description of Changes
are limited to 2.25–3.6 V only if EBTS = 0; V
OH_S
= –2.0 mA’ from the 1st line to the second line and deleted
OL_S
OH_S
Revision History for the MPC5553 Data Sheet
= 2.0 mA):’ Created a left-justified second line
= –1.0 mA.’
IL
DDEH
and V
STBY
’ and put ‘0.85 × V
OH_S
IH
.
to ground.
= –2.0 mA):’
DDE2
DDEH
and V
’ on the last
DDE3
have
63