C8051F353 Silicon Laboratories Inc, C8051F353 Datasheet - Page 115

• Manufacturer Part Number: C8051F353
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F353

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
Bit7
R
-
UNUSED. Read = 0. Write = don’t care.
FERROR: Flash Error Indicator.
0: Source of last reset was not a Flash read/write/erase error.
1: Source of last reset was a Flash read/write/erase error.
C0RSEF: Comparator0 Reset Enable and Flag.
0: Read: Source of last reset was not Comparator0. Write: Comparator0 is not a reset
source.
1: Read: Source of last reset was Comparator0. Write: Comparator0 is a reset source
(active-low).
SWRSF: Software Reset Force and Flag.
0: Read: Source of last reset was not a write to the SWRSF bit. Write: No Effect.
1: Read: Source of last was a write to the SWRSF bit. Write: Forces a system reset.
WDTRSF: Watchdog Timer Reset Flag.
0: Source of last reset was not a WDT timeout.
1: Source of last reset was a WDT timeout.
MCDRSF: Missing Clock Detector Flag.
0: Read: Source of last reset was not a Missing Clock Detector timeout. Write: Missing
Clock Detector disabled.
1: Read: Source of last reset was a Missing Clock Detector timeout. Write: Missing Clock
Detector enabled; triggers a reset if a missing clock condition is detected.
PORSF: Power-On Reset Force and Flag.
This bit is set anytime a power-on reset occurs. Writing this bit enables/disables the V
monitor as a reset source. Note: writing ‘1’ to this bit before the V
and stabilized may cause a system reset. See register VDM0CN (Figure 14.3)
0: Read: Last reset was not a power-on or V
reset source.
1: Read: Last reset was a power-on or V
Write: V
PINRSF: HW Pin Reset Flag.
0: Source of last reset was not /RST pin.
1: Source of last reset was /RST pin.
FERROR C0RSEF
Bit6
R
DD
monitor is a reset source.
Figure 14.4. RSTSRC: Reset Source Register
R/W
Bit5
SWRSF
R/W
Bit4
WDTRSF MCDRSF
Rev. 0.4
Bit3
DD
R
monitor reset; all other reset flags indeterminate.
DD
monitor reset. Write: V
R/W
Bit2
C8051F350/1/2/3
PORSF
R/W
Bit1
DD
SFR Address:
DD
PINRSF
monitor is enabled
Bit0
monitor is not a
R
0xEF
Reset Value
Variable
DD
115