ATMEGA161-8PI Atmel, ATMEGA161-8PI Datasheet - Page 51

• Manufacturer Part Number: ATMEGA161-8PI
• Description: IC AVR MCU 16K 8MHZ IND 40-DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA161-8PI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -
• Other names: ATMEGA1618PI

1228D–AVR–02/07
• Bits 5, 4
The COM1B1 and COM1B0 control bits determine any output pin action following a
compare match in Timer/Counter1. Any output pin actions affect pin OC1B (Output
CompareB). This is an alternative function to an I/O port, and the corresponding direc-
tion control bit must be set (one) to control an output pin. The following control
configuration is given:
Table 14. Compare 1 Mode Select
Note:
In PWM mode, these bits have a different function. Refer to Table 18 for a detailed
description.
• Bit 3
Writing a logical “1” to this bit forces a change in the compare match output pin PD5
according to the values already set in COM1A1 and COM1A0. If the COM1A1 and
COM1A0 bits are written in the same cycle as FOC1A, the new settings will not take
effect until the next compare match or forced compare match occurs. The Force Output
Compare bit can be used to change the output pin without waiting for a compare match
in the timer. The automatic action programmed in COM1A1 and COM1A0 happens as if
a Compare Match had occurred, but no interrupt is generated and it will not clear the
timer even if CTC1 in TCCR1B is set. The FOC1A bit will always be read as zero. The
setting of the FOC1A bit has no effect in PWM mode.
• Bit 2
Writing a logical “1” to this bit forces a change in the compare match output pin PE2
according to the values already set in COM1B1 and COM1B0. If the COM1B1 and
COM1B0 bits are written in the same cycle as FOC1B, the new settings will not take
effect until the next compare match or forced compare match occurs. The Force Output
Compare bit can be used to change the output pin without waiting for a compare match
in the timer. The automatic action programmed in COM1B1 and COM1B0 happens as if
a Compare Match had occurred, but no interrupt is generated. The FOC1B bit will
always be read as zero. The setting of the FOC1B bit has no effect in PWM mode.
COM1X1
0
0
1
1
–
–
1. X = A or B
FOC1A: Force Output Compare1A
FOC1B: Force Output Compare1B
–
COM1B1, COM1B0: Compare Output Mode1B, Bits 1 and 0
COM1X0
0
1
0
1
Description
Timer/Counter1 disconnected from output pin OC1X
Toggle the OC1X output line.
Clear the OC1X output line (to zero).
Set the OC1X output line (to one).
(1)
ATmega161(L)
51