SAK-XC164CM-16F20F BA Infineon Technologies, SAK-XC164CM-16F20F BA Datasheet - Page 28

• Manufacturer Part Number: SAK-XC164CM-16F20F BA
• Description: IC MCU 16BIT FLASH 64-LQFP
• Manufacturer: Infineon Technologies
• Series: XC16xr

Specifications of SAK-XC164CM-16F20F BA

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 64-LFQFP
• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, SPI, UART/USART
• Peripherals: PWM, WDT
• Number Of I /o: 47
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.7 V
• Data Converters: A/D 14x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: XC164x
• Core: C166S V2
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: ASC/CAN/SSC
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 47
• Number Of Timers: 5
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK166, CA166, AR166, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Packages: PG-LQFP-64
• Max Clock Frequency: 20.0 MHz
• Sram (incl. Cache): 8.0 KByte
• Can Nodes: 2
• A / D Input Lines (incl. Fadc): 14
• Program Memory: 128.0 KByte
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: B158-H8961-X-X-7600IN - KIT EASY XC164CMXC164CMUCANIN - KIT U-CAN STARTER XC164CM
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000245661

3.5
The CAPCOM unit supports generation and control of timing sequences on up to
16 channels with a maximum resolution of 1 system clock cycle (8 cycles in staggered
mode). The CAPCOM unit is typically used to handle high speed I/O tasks such as pulse
and waveform generation, pulse width modulation (PWM), Digital to Analog (D/A)
conversion, software timing, or time recording relative to external events.
Two 16-bit timers (T7/T8) with reload registers provide two independent time bases for
the capture/compare register array.
The input clock for the timers is programmable to several prescaled values of the internal
system clock, or may be derived from an overflow/underflow of timer T6 in module GPT2.
This provides a wide range of variation for the timer period and resolution and allows
precise adjustments to the application specific requirements. In addition, an external
count input for CAPCOM timer T7 allows event scheduling for the capture/compare
registers relative to external events.
The capture/compare register array contains 16 dual purpose capture/compare
registers, each of which may be individually allocated to either CAPCOM timer (T7 or T8,
respectively), and programmed for capture or compare function.
10 registers of the CAPCOM2 module have each one port pin associated with it which
serves as an input pin for triggering the capture function, or as an output pin to indicate
the occurrence of a compare event.
Table 6
Compare Modes
Mode 0
Mode 1
Mode 2
Mode 3
Double Register
Mode
Single Event Mode
When a capture/compare register has been selected for capture mode, the current
contents of the allocated timer will be latched (‘captured’) into the capture/compare
Data Sheet
Capture/Compare Unit (CAPCOM2)
Compare Modes (CAPCOM2)
Function
Interrupt-only compare mode;
Several compare interrupts per timer period are possible
Pin toggles on each compare match;
Several compare events per timer period are possible
Interrupt-only compare mode;
Only one compare interrupt per timer period is generated
Pin set ‘1’ on match; pin reset ‘0’ on compare timer overflow;
Only one compare event per timer period is generated
Two registers operate on one pin;
Pin toggles on each compare match;
Several compare events per timer period are possible
Generates single edges or pulses;
Can be used with any compare mode
26
Functional Description
Derivatives
V1.4, 2007-03
XC164CM