MC908GR32ACFAER Freescale Semiconductor, MC908GR32ACFAER Datasheet - Page 197

• Manufacturer Part Number: MC908GR32ACFAER
• Description: IC MCU 32K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR32ACFAER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1.5KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

14.6.1 Wait Mode
In wait mode, the CPU clocks are inactive while the peripheral clocks continue to run.
the timing for wait mode entry.
A module that is active during wait mode can wakeup the CPU with an interrupt if the interrupt is enabled.
Stacking for the interrupt begins one cycle after the WAIT instruction during which the interrupt occurred.
In wait mode, the CPU clocks are inactive. Refer to the wait mode subsection of each module to see if the
module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode.
Wait mode also can be exited by a reset or break. A break interrupt during wait mode sets the SIM break
stop/wait bit, SBSW, in the SIM break status register (BSR). If the COP disable bit, COPD, in the
CONFIG1 register is 0, then the computer operating properly module (COP) is enabled and remains
active in wait mode.
Figure 14-17
Freescale Semiconductor
and
EXITSTOPWAIT
Note: EXITSTOPWAIT = RST pin, CPU interrupt, or break interrupt
CGMXCLK
MC68HC908GR60A • MC68HC908GR48A • MC68HC908GR32A Data Sheet, Rev. 5
R/W
Figure 14-18
IAB
IDB
Note:
RST
IDB
IAB
IDB
IAB
Figure 14-17. Wait Recovery from Interrupt or Break
$A6
Previous data can be operand data or the WAIT opcode, depending on the
last instruction.
WAIT ADDR
Figure 14-18. Wait Recovery from Internal Reset
$A6
$6E0B
$A6
show the timing for WAIT recovery.
PREVIOUS DATA
Figure 14-16. Wait Mode Entry Timing
$6E0B
$A6
$A6
WAIT ADDR + 1
$A6
CYCLES
$6E0C
32
NEXT OPCODE
$01
$00FF
CYCLES
32
$0B
SAME
$00FE
$6E
SAME
RST VCT H
$00FD
SAME
RST VCT L
$00FC
SAME
Figure 14-16
Low-Power Modes
shows
197