MC9S08QD2MSCR Freescale Semiconductor, MC9S08QD2MSCR Datasheet - Page 69

• Manufacturer Part Number: MC9S08QD2MSCR
• Description: IC MCU 8BIT 8-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QD2MSCR

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 16MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 4
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: S08QD
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QD4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

1
2
6.4
6.4.1
This section provides information about the registers associated with the parallel I/O ports.
Refer to tables in
for all parallel I/O. This section refers to registers and control bits only by their names. A Freescale
Semiconductor-provided equate or header file normally is used to translate these names into the
appropriate absolute addresses.
6.4.1.1
Freescale Semiconductor
Reads of bit PTAD5 always return the pin value of PTA5, regardless of the value stored in bit PTADD5.
Reads of bit PTAD4 always return the contents of PTAD4, regardless of the value stored in bit PTADD4.
Reset:
•
•
•
W
R
In stop1 mode, all internal registers including parallel I/O control and data registers are powered
off. Each of the pins assumes its default reset state (output buffer and internal pullup disabled).
Upon exit from stop1, all pins must be re-configured the same as if the MCU had been reset.
Stop2 mode is a partial power-down mode, whereby latches maintain the pin state as before the
STOP instruction was executed. CPU register status and the state of I/O registers must be saved in
RAM before the STOP instruction is executed to place the MCU in stop2 mode. Upon recovery
from stop2 mode, before accessing any I/O, the user must examine the state of the PPDF bit in the
SPMSC2 register. If the PPDF bit is 0, I/O must be initialized as if a power on reset had occurred.
If the PPDF bit is 1, I/O data previously stored in RAM, before the STOP instruction was executed,
peripherals previously enabled will require being initialized and restored to their pre-stop
condition. The user must then write a 1 to the PPDACK bit in the SPMSC2 register. Access of pins
is now permitted again in the user’s application program.
In stop3 mode, all pin states are maintained because internal logic stays powered up. Upon
recovery, all pin functions are the same as before entering stop3.
Parallel I/O Registers
Port A Registers
Port A Data (PTAD)
0
7
0
Chapter 4, “Memory Map and Register
0
0
6
Figure 6-2. Port A Data Register (PTAD)
MC9S08QD4 Series MCU Data Sheet, Rev. 6
PTAD5
0
5
1
PTAD4
0
4
2
Definition,” for the absolute address assignments
PTAD3
3
0
PTAD2
Chapter 6 Parallel Input/Output Control
0
2
PTAD1
0
1
PTAD0
0
0
69