W77E058A40DL Nuvoton Technology Corporation of America, W77E058A40DL Datasheet - Page 66

• Manufacturer Part Number: W77E058A40DL
• Description: IC MCU 8-BIT 32K FLASH 40-DIP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: W77r

Specifications of W77E058A40DL

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, Serial Port
• Peripherals: POR, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP
• Cpu Family: W77
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: UART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

14.3 Mode 2
This mode uses a total of 11 bits in asynchronous full-duplex communication. The functional
description is shown in the figure below. The frame consists of one start bit (0), 8 data bits (LSB first),
a programmable 9th bit (TB8) and a stop bit (0). The 9th bit received is put into RB8. The baud rate is
programmable to 1/32 or 1/64 of the oscillator frequency, which is determined by the SMOD bit in
PCON SFR. Transmission begins with a write to SBUF. The serial data is brought out on to TxD pin at
C1 following the first roll-over of the divide by 16 counter. The next bit is placed on TxD pin at C1
following the next rollover of the divide by 16 counter. Thus the transmission is synchronized to the
divide by 16 counter, and not directly to the write to SBUF signal. After all 9 bits of data are
transmitted, the stop bit is transmitted. The TI flag is set in the C1 state after the stop bit has been put
out on TxD pin. This will be at the 11th rollover of the divide by 16 counter after a write to SBUF.
Reception is enabled only if REN is high. The serial port actually starts the receiving of serial data, with
the detection of a falling edge on the RxD pin. The 1-to-0 detector continuously monitors the RxD line,
sampling it at the rate of 16 times the selected baud rate. When a falling edge is detected, the divide
by 16 counter is immediately reset. This helps to align the bit boundaries with the rollovers of the
divide by 16 counter. The 16 states of the counter effectively divide the bit time into 16 slices. The bit
detection is done on a best of three basis. The bit detector samples the RxD pin, at the 8th, 9th and
10th counter states. By using a majority 2 of 3 voting system, the bit value is selected. This is done to
improve the noise rejection feature of the serial port.
If the first bit detected after the falling edge of RxD pin, is not 0, then this indicates an invalid start bit,
and the reception is immediately aborted. The serial port again looks for a falling edge in the RxD line.
If a valid start bit is detected, then the rest of the bits are also detected and shifted into the SBUF. After
(SMOD_1)
SMOD=
div. by 4
div. by 64
div. by 1024 osc/512
Mode
Clock Source
SAMPLE
RXD
2
0
osc/2
osc/32
input
1
DETECTOR
1-TO-0
16
16
Write to
SBUF
RX CLOCK
RX START
TX START
TX CLOCK
CONTROLLER
DETECTOR
SERIAL
Figure 22. Serial Port Mode 2
BIT
Data Bus
Internal
RX SHIFT
SHIFT
LOAD
SBUF
- 66 -
TX
TB8
RI
TI
CLOCK
SIN
Receive Shift Register
PAROUT
START
LOAD
STOP
CLOCK
D8
PARIN
Transmit Shift Register
D8
SOUT
SBUF
RB8
Serial Port
Interrupt
Read
SBUF
W77E058A
TXD
Internal
Data
Bus