ATMEGA1280-16AUR Atmel, ATMEGA1280-16AUR Datasheet - Page 368

• Manufacturer Part Number: ATMEGA1280-16AUR
• Description: MCU AVR 128K FLASH 16MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA1280-16AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFPATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Notes:
2549M–AVR–09/10
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40°C to 85°C, V
1. "Max" means the highest value where the pin is guaranteed to be read as low.
2. "Min" means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
conditions (non-transient), the following must be observed:
ATmega1281/2561:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
ATmega640/1280/2560:
1.)The sum of all IOL, for ports J0-J7, A0-A7, G2 should not exceed 200 mA.
2.)The sum of all IOL, for ports C0-C7, G0-G1, D0-D7, L0-L7 should not exceed 200 mA.
3.)The sum of all IOL, for ports G3-G4, B0-B7, H0-B7 should not exceed 200 mA.
4.)The sum of all IOL, for ports E0-E7, G5 should not exceed 100 mA.
5.)The sum of all IOL, for ports F0-F7, K0-K7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
ATmega1281/2561:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
ATmega640/1280/2560:
1)The sum of all IOH, for ports J0-J7, G2, A0-A7 should not exceed 200 mA.
2)The sum of all IOH, for ports C0-C7, G0-G1, D0-D7, L0-L7 should not exceed 200 mA.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
(5)
(ATmega640/1280/2560/1V)
Active 4MHz, V
(ATmega640/1280/2560/1L)
Active 8MHz, V
(ATmega640/1280/1281/2560/2561)
Idle 1MHz, V
WDT disabled, V
V
V
V
Condition
Active 1MHz, V
(ATmega640/1280/2560/1V)
Idle 4MHz, V
(ATmega640/1280/2560/1L)
Idle 8MHz, V
(ATmega640/1280/1281/2560/2561)
WDT enabled, V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
ATmega640/1280/1281/2560/2561
Min.
-50
Typ.
0.14
<10
750
500
0.5
3.2
0.7
2.7
10
<5
<1
Max.
0.22
0.8
1.1
7.5
14
15
40
50
5
4
Units
mA
mV
µA
nA
ns
368