ATMEGA8535-16PU Atmel, ATMEGA8535-16PU Datasheet - Page 46

• Manufacturer Part Number: ATMEGA8535-16PU
• Description: IC AVR MCU 8K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• A/d Inputs: 8-Channel, 10-Bit
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 32
• Interface: SPI/TWI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 8K Bytes
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 32
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

46
ATmega8535(L)
Table 20. Reset and Interrupt Vectors Placement
Note:
The most typical and general program setup for the Reset and Interrupt Vector
Addresses in ATmega8535 is:
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2K bytes and
the IVSEL bit in the GICR Register is set before any interrupts are enabled, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
BOOTRST
AddressLabels
0x000
0x001
0x002
0x003
0x004
0x005
0x006
0x007
0x008
0x009
0x00A
0x00B
0x00C
0x00D
0x00E
0x00F
0x010
0x011
0x012
0x013
0x014
;
0x015 RESET:
0x016
0x017
0x018
0x019
0x020
...
1
1
0
0
1. The Boot Reset Address is shown in Table 93 on page 233. For the BOOTRST Fuse
...
(1)
“1” means unprogrammed while “0” means programmed.
IVSEL
0
1
0
1
Code
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
ldi
out
ldi
out
sei
<instr> xxx
...
Reset Address
0x0000
0x0000
Boot Reset Address
Boot Reset Address
RESET
EXT_INT0
EXT_INT1
TIM2_COMP
TIM2_OVF
TIM1_CAPT
TIM1_COMPA
TIM1_COMPB
TIM1_OVF
TIM0_OVF
SPI_STC
USART_RXC
USART_UDRE
USART_TXC
ADC
EE_RDY
ANA_COMP
TWSI
EXT_INT2
TIM0_COMP
SPM_RDY
r16,high(RAMEND) ; Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
Comments
; Reset Handler
; IRQ0 Handler
; IRQ1 Handler
; Timer2 Compare Handler
; Timer2 Overflow Handler
; Timer1 Capture Handler
; Timer1 Compare A Handler
; Timer1 Compare B Handler
; Timer1 Overflow Handler
; Timer0 Overflow Handler
; SPI Transfer Complete Handler
; USART RX Complete Handler
; UDR Empty Handler
; USART TX Complete Handler
; ADC Conversion Complete Handler
; EEPROM Ready Handler
; Analog Comparator Handler
; Two-wire Serial Interface Handler
; IRQ2 Handler
; Timer0 Compare Handler
; Store Program Memory Ready Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Interrupt Vectors Start Address
0x0001
Boot Reset Address + 0x0001
0x0001
Boot Reset Address + 0x0001
2502G–AVR–04/05