ATTINY26L-8PU Atmel, ATTINY26L-8PU Datasheet - Page 62

• Manufacturer Part Number: ATTINY26L-8PU
• Description: IC MCU AVR 2K 5V 8MHZ 20-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY26L-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: 2-Wire/ISP/SM-Bus/SPI/UART/USI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Controller Family/series: AVR Tiny
• No. Of I/o's: 16
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATTINY26L-8PJ; ATTINY26L-8PJ

External Interrupt
Pin Change Interrupt
62
ATtiny26(L)
The External Interrupt is triggered by the INT0 pin. Observe that, if enabled, the interrupt
will trigger even if the INT0 pin is configured as an output. This feature provides a way of
generating a software interrupt. The External Interrupt can be triggered by a falling or
rising edge, a pin change, or a low level. This is set up as indicated in the specification
for the MCU Control Register – MCUCR. When the External Interrupt is enabled and is
configured as level triggered, the interrupt will trigger as long as the pin is held low.
The changed level is sampled twice by the Watchdog Oscillator clock, and if both these
samples have the required level, the MCU will wake up. The period of the Watchdog
Oscillator is 1.0
tor is voltage dependent as shown in “Electrical Characteristics” on page 126.
The pin change interrupt is triggered by any change on any I/O pin of Port B and pins
PA3, PA6, and PA7, if the interrupt is enabled and alternate function of the pin does not
mask out the interrupt. The bit PCIE1 in GIMSK enables interrupt from pins PB[7:4],
PA[7:6], and PA[3]. PCIE0 enables interrupt on digital pins PB[3:0].
The pin change interrupt is different from other interrupts in two ways. First, pin change
interrupt enable bits PCIE1 and PCIE0 also mask the flag if they are not set. The normal
operation on most interrupts is that the flag is always active and only the execution of
the interrupt is masked by the interrupt enable.
Secondly, please note that pin change interrupt is disabled for any pin that is configured
as an alternate function. For example, no pin change interrupt is generated from pins
that are configured as AREF, AIN0 or AIN1, OC1A, OC1A, OC1B, OC1B, XTAL1, or
XTAL2 in a fuse selected clock option, Timer0 clocking, or RESET function. See Table
30 for alternate functions which mask the pin change interrupt and how the function is
enabled. For example pin change interrupt on the PB0 is disabled when USI Two-wire
mode or USI Three-wire mode or Timer/Counter1 inverted output compare is enabled.
If the interrupt is enabled, the interrupt will trigger even if the changing pin is configured
as an output. This feature provides a way of generating a software interrupt. Also
observe that the pin change interrupt will trigger even if the pin activity triggers another
interrupt, for example the external interrupt. This implies that one external event might
cause several interrupts.
The value of the programmed fuse is “0” and unprogrammed is “1”. Each of the lines
enables the alternate function so “or” function of the lines enables the function.
µs
(nominal) at 3.0V and 25°C. The frequency of the Watchdog Oscilla-
1477F–AVR–12/04