PIC16F1934-E/ML Microchip Technology, PIC16F1934-E/ML Datasheet - Page 284

• Manufacturer Part Number: PIC16F1934-E/ML
• Description: IC PIC MCU FLASH 256KX7 44-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F1934-E/ML

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 44-QFN
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART/MI2C/SPI
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F193X/LF193X
22.3.3
To enable the serial port, SSP Enable bit, SSPEN of the
SSPCON1 register, must be set. To reset or reconfig-
ure SPI mode, clear the SSPEN bit, re-initialize the
SSPCONx registers and then set the SSPEN bit. This
configures the SDI, SDO, SCK and SS pins as serial
port pins. For the pins to behave as the serial port func-
tion, some must have their data direction bits (in the
TRIS register) appropriately programmed as follows:
• SDI must have corresponding TRIS bit set
• SDO must have corresponding TRIS bit cleared
• SCK (Master mode) must have corresponding
• SCK (Slave mode) must have corresponding
• SS must have corresponding TRIS bit set
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.
FIGURE 22-4:
DS41364A-page 282
TRIS bit cleared
TRIS bit set
ENABLING SPI I/O
SPI Master SSPM<3:0> = 00xx
MSb
Serial Input Buffer
Processor 1
Shift Register
SPI MASTER/SLAVE CONNECTION
(SSPBUF)
(SSPSR)
= 1010
LSb
General I/O
SCK
SDO
SDI
Preliminary
Serial Clock
Slave Select
(optional)
22.3.4
Figure 22-4 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCK signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data (Slave sends dummy data)
• Master sends data (Slave sends data)
• Master sends dummy data (Slave sends data)
SDO
SCK
SDI
SS
TYPICAL CONNECTION
SPI Slave SSPM<3:0> = 010x
MSb
Serial Input Buffer
Shift Register
(SSPBUF)
(SSPSR)
Processor 2
© 2008 Microchip Technology Inc.
LSb