ATTINY2313A-MUR Atmel, ATTINY2313A-MUR Datasheet - Page 153

• Manufacturer Part Number: ATTINY2313A-MUR
• Description: MCU AVR 2K FLASH 20MHZ 20QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY2313A-MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -

15.8.4
8246A–AVR–11/09
UCSRC – USART MSPIM Control and Status Register C
• Bit 6 – TXCIE: TX Complete Interrupt Enable
Writing this bit to one enables interrupt on the TXC Flag. A USART Transmit Complete interrupt
will be generated only if the TXCIE bit is written to one, the Global Interrupt Flag in SREG is writ-
ten to one and the TXC bit in UCSRA is set.
• Bit 5 – UDRIE: USART Data Register Empty Interrupt Enable
Writing this bit to one enables interrupt on the UDRE Flag. A Data Register Empty interrupt will
be generated only if the UDRIE bit is written to one, the Global Interrupt Flag in SREG is written
to one and the UDRE bit in UCSRA is set.
• Bit 4 – RXEN: Receiver Enable
Writing this bit to one enables the USART Receiver in MSPIM mode. The Receiver will override
normal port operation for the RxD pin when enabled. Disabling the Receiver will flush the receive
buffer. Only enabling the receiver in MSPI mode (i.e. setting RXEN=1 and TXEN=0) has no
meaning since it is the transmitter that controls the transfer clock and since only master mode is
supported.
• Bit 3 – TXEN: Transmitter Enable
Writing this bit to one enables the USART Transmitter. The Transmitter will override normal port
operation for the TxD pin when enabled. The disabling of the Transmitter (writing TXEN to zero)
will not become effective until ongoing and pending transmissions are completed, i.e., when the
Transmit Shift Register and Transmit Buffer Register do not contain data to be transmitted.
When disabled, the Transmitter will no longer override the TxD port.
• Bit 2:0 – Reserved Bits in MSPI mode
When in MSPI mode, these bits are reserved for future use. For compatibility with future devices,
these bits must be written to zero when UCSRB is written.
• Bit 7:6 – UMSEL1:0: USART Mode Select
These bits select the mode of operation of the USART as shown in
USART Control and Status Register C” on page 139
operation. The MSPIM is enabled when both UMSEL bits are set to one. The UDORD, UCPHA,
and UCPOL can be set in the same write operation where the MSPIM is enabled.
Table 15-4.
Bit
0x03 (0x23)
Read/Write
Initial Value
UMSEL1
UMSEL Bits Settings
UMSEL1
0
0
1
1
R/W
7
0
UMSEL0
R/W
6
0
R
5
0
-
UMSEL0
R
4
0
-
1
0
1
0
R
3
0
-
for full description of the normal USART
UDORD
R/W
2
1
Mode
Asynchronous USART
Synchronous USART
Reserved
Master SPI (MSPIM)
Table
UCPHA
R/W
1
1
15-4. See
UCPOL
R/W
0
0
“UCSRC –
UCSRC
153