DF2338VFC25V Renesas Electronics America, DF2338VFC25V Datasheet - Page 712

• Manufacturer Part Number: DF2338VFC25V
• Description: IC H8S/2300 MCU FLASH 144QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2300r

Specifications of DF2338VFC25V

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: SCI, SmartCard
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 106
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12x10b; D/A 4x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-QFP
• For Use With: EDK2329 - DEV EVALUATION KIT H8S/2329
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

15.3.4
Table 15.3 shows a bit map of the registers used by the smart card interface.
Bits indicated as 0 or 1 must be set to the value shown. The setting of other bits is described
below.
Table 15.3 Smart Card Interface Register Settings
Register
SMR
BRR
SCR
TDR
SSR
RDR
SCMR
Notes: — : Unused bit.
SMR Settings: The GM bit is cleared to 0 in normal smart card interface mode, and set to 1 in
GSM mode. The O/E bit is cleared to 0 if the IC card is of the direct convention type, and set to 1
if of the inverse convention type.
Bits CKS1 and CKS0 select the clock source of the built-in baud rate generator, and bits BCP1
and BCP0 select the number of base clock cycles during transfer of one bit. For details, see section
15.3.5, Clock.
The BLK bit is cleared to 0 when using the normal smart card interface mode, and set to 1 when
using block transfer mode.
BRR Setting: BRR is used to set the bit rate. See section 15.3.5, Clock, for the method of
calculating the value to be set.
SCR Settings: The function of the TIE, RIE, TE, and RE bits is the same as for the normal SCI.
For details, see section 14, Serial Communication Interface (SCI).
Bits CKE1 and CKE0 specify the clock output. When the GM bit in SMR is cleared to 0, set these
bits to B'00 if a clock is not to be output, or to B'01 if a clock is to be output. When the GM bit in
SMR is set to 1, clock output is performed. The clock output can also be fixed high or low.
Rev.4.00 Sep. 07, 2007 Page 680 of 1210
REJ09B0245-0400
* The CKE1 bit must be cleared to 0 when the GM bit in SMR is cleared to 0.
Register Settings
Bit 7
GM
BRR7
TIE
TDR7
TDRE
RDR7
—
Bit 6
BLK
BRR6
RIE
TDR6
RDRF
RDR6
—
Bit 5
1
BRR5
TE
TDR5
ORER
RDR5
—
RE
ERS
Bit 4
O/E
BRR4
TDR4
RDR4
—
Bit
BRR3
0
PER
Bit 3
BCP1
TDR3
RDR3
SDIR
Bit 2
BCP0
BRR2
0
TDR2
TEND
RDR2
SINV
Bit 1
CKS1
BRR1
CKE1 *
TDR1
0
RDR1
—
Bit 0
CKS0
BRR0
CKE0
TDR0
0
RDR0
SMIF