PIC17C44-25/L Microchip Technology, PIC17C44-25/L Datasheet - Page 60

• Manufacturer Part Number: PIC17C44-25/L
• Description: IC MCU OTP 8KX16 PWM 44PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C44-25/L

• Core Size: 8-Bit
• Program Memory Size: 16KB (8K x 16)
• Core Processor: PIC
• Speed: 25MHz
• Connectivity: UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 454 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 44-PLCC
• Controller Family/series: PIC17
• No. Of I/o's: 33
• Ram Memory Size: 454Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 2
• Embedded Interface Type: USART
• Rohs Compliant: Yes
• Processor Series: PIC17C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 454 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164317 - MODULE SKT MPLAB PM3 44PLCCDVA17XL441 - DEVICE ADAPTER FOR PIC17C42A309-1007 - ADAPTER 44-PLCC ZIF TO 40-DIPAC174002 - MODULE SKT PROMATEII 44PLCC
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

PIC17C4X
9.4
PORTD is an 8-bit bi-directional port. The correspond-
ing data direction register is DDRD. A '1' in DDRD con-
figures the corresponding port pin as an input. A '0' in
the DDRC register configures the corresponding port
pin as an output. Reading PORTD reads the status of
the pins, whereas writing to it will write to the port latch.
PORTD is multiplexed with the system bus. When
operating as the system bus, PORTD is the high order
byte of the address/data bus (AD15:AD8). The timing
for the system bus is shown in the Electrical Character-
istics section.
FIGURE 9-7:
DS30412C-page 60
Note: I/O pins have protection diodes to V
Note:
PORTD and DDRD Registers
This port is configured as the system bus
when the device’s configuration bits are
selected to Microprocessor or Extended
Microcontroller modes. In the two other
microcontroller modes, this port is a gen-
eral purpose I/O.
PORTD BLOCK DIAGRAM (IN I/O PORT MODE)
TTL
Input
Buffer
DD
0
1
and Vss.
Data
Port
Q
Q
R
CK
CK
S
D
D
Example 9-3 shows the instruction sequence to initial-
ize PORTD. The Bank Select Register (BSR) must be
selected to Bank 1 for the port to be initialized.
EXAMPLE 9-3:
MOVLB 1
CLRF
MOVLW 0xCF
MOVWF DDRD
PORTD
INSTRUCTION READ
INITIALIZING PORTD
;
;
;
;
;
;
;
;
;
;
to D_Bus
DATA/ADDR_OUT
1996 Microchip Technology Inc.
Select Bank 1
Initialize PORTD data
Value used to initialize
Set RD<3:0> as inputs
data direction
latches before setting
the data direction
register
RD<5:4> as outputs
RD<7:6> as inputs
WR_PORTD
RD_PORTD
WR_DDRD
RD_DDRD
DRV_SYS
Data Bus
EX_EN
IR
SYS BUS
Control