AT89C5131A-S3SUM Atmel, AT89C5131A-S3SUM Datasheet - Page 14

• Manufacturer Part Number: AT89C5131A-S3SUM
• Description: IC 8051 MCU FLASH 32K USB 52PLCC
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5131A-S3SUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-PLCC
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: 2-Wire, EUART, SPI, USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89STK-05
• Minimum Operating Temperature: - 40 C
• Package: 52PLCC
• Device Core: 8051
• Family Name: 89C
• Maximum Speed: 48 MHz
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

5. Clock Controller
5.1
Figure 5-1.
5.2
14
Introduction
Oscillator
AT89C5130A/31A-M
X1
X2
Oscillator Block Diagram
PLLCON.2
EXT48
The AT89C5130A/31A-M clock controller is based on an on-chip oscillator feeding an on-chip
Phase Lock Loop (PLL). All the internal clocks to the peripherals and CPU core are generated
by this controller.
The AT89C5130A/31A-M X1 and X2 pins are the input and the output of a single-stage on-chip
inverter (see Figure 5-1) that can be configured with off-chip components as a Pierce oscillator
(see Figure 5-2). Value of capacitors and crystal characteristics are detailed in the section “DC
Characteristics”.
The X1 pin can also be used as input for an external 48 MHz clock.
The clock controller outputs three different clocks as shown in Figure 5-1:
These clocks are enabled or disabled depending on the power reduction mode as detailed in
Section “Power Management”, page 155.
Two types of clock sources can be used for CPU:
PCON.1
• a clock for the CPU core
• a clock for the peripherals which is used to generate the Timers, PCA, WD, and Port
• a clock for the USB controller
• Crystal oscillator on X1 and X2 pins: Up to 32 MHz (Amplifier Bandwidth)
• External clock on X1 pin: Up to 48MHz
PD
sampling clocks
PLL
0
1
÷
2
CKCON.0
X2
0
1
PCON.0
IDL
USB
Clock
Peripheral
Clock
CPU Core
Clock
4337K–USB–04/08