PIC18F2320-I/SP Microchip Technology, PIC18F2320-I/SP Datasheet - Page 223

• Manufacturer Part Number: PIC18F2320-I/SP
• Description: IC MCU FLASH 4KX16 EEPROM 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2320-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

20.0
The comparator module contains two analog compara-
tors. The inputs and outputs for the comparators are
multiplexed with the RA0 through RA5 pins. The on-
chip voltage reference (Section 21.0 “Comparator
Voltage Reference Module”) can also be an input to
the comparators.
The CMCON register, shown as Register 20-1,
controls the comparator module’s input and output
multiplexers.
comparator configurations is shown in Figure 20-1.
REGISTER 20-1:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
C2OUT
R-0
COMPARATOR MODULE
A
C2OUT: Comparator 2 Output bit
When C2INV = 0:
1 = C2 V
0 = C2 V
When C2INV = 1:
1 = C2 V
0 = C2 V
C1OUT: Comparator 1 Output bit
When C1INV = 0:
1 = C1 V
0 = C1 V
When C1INV = 1:
1 = C1 V
0 = C1 V
C2INV: Comparator 2 Output Inversion bit
1 = C2 output inverted
0 = C2 output not inverted
C1INV: Comparator 1 Output Inversion bit
1 = C1 output inverted
0 = C1 output not inverted
CIS: Comparator Input Switch bit
When CM2:CM0 = 110:
1 = C1 V
0 = C1 V
CM2:CM0: Comparator Mode bits
Figure 20-1 shows the Comparator modes and the CM2:CM0 bit settings.
block
C1OUT
C2 V
C2 V
R-0
CMCON: COMPARATOR CONTROL REGISTER
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
diagram
+ > C2 V
+ < C2 V
+ < C2 V
+ > C2 V
+ > C1 V
+ < C1 V
+ < C1 V
+ > C1 V
- connects to RA3/AN3
- connects to RA2/AN2
- connects to RA0/AN0
- connects to RA1/AN1
W = Writable bit
‘1’ = Bit is set
C2INV
R/W-0
IN
IN
IN
IN
IN
IN
IN
IN
of
-
-
-
-
-
-
-
-
the
PIC18F2220/2320/4220/4320
various
C1INV
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
20.1
There are eight modes of operation for the comparators.
The CM bits (CMCON<2:0>) are used to select these
modes. Figure 20-1 shows the eight possible modes.
The TRISA register controls the data direction of the
comparator pins for each mode. If the Comparator mode
is changed, the comparator output level may not be valid
for the specified mode change delay shown in the
Electrical Specifications (see Section 26.0 “Electrical
Characteristics”).
CIS
Note:
Comparator Configuration
Comparator interrupts should be disabled
during a Comparator mode change.
Otherwise, a false interrupt may occur.
R/W-1
CM2
x = Bit is unknown
R/W-1
CM1
DS39599G-page 221
R/W-1
CM0
bit 0