HCPL-7720-000E Avago Technologies US Inc., HCPL-7720-000E Datasheet - Page 9

• Manufacturer Part Number: HCPL-7720-000E
• Description: OPTOCOUPLER CMOS 25MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-7720-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 25MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 0.008 us
• Maximum Forward Diode Current: 10 mA
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 25 MBd
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10µA
• Output Voltage: 5V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1689-5

Package Characteristics
Notes:
10. The Input-Output Momentary With stand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
11. C
Figure 1. Typical output voltage vs. input volt-
age.
9
Parameter
Input-Output Momentary
Withstand Voltage
Resistance
(Input-Output)
Capacitance
(Input-Output)
Input Capacitance
Input IC Junction-to-Case
Thermal Resistance
Output IC Junction-to-Case
Thermal Resistance
Package Power Dissipation
9. In accordance with UL1577, each HCPL-072X is proof tested by applying an insulation test voltage ≥4500 V
1. Absolute Maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
2. The LED is ON when V
3. t
4. PWD is defined as |t
5. t
6. CM
7. Unloaded dynamic power dissipation is calculated as follows: C
8. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
guarantee functionality.
t
the recommended operating conditions.
mode voltage slew rate that can be sustained while maintaining
and falling common mode voltage edges.
current limit, I
current limit. I
voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Avago Application Note 1074 entitled
“Optocoupler Input-Output Endurance Voltage. ”
PHL
PLH
PSK
5
4
3
2
1
0
I
is the capacitance measured at pin 2 (V
0
H
is equal to the magnitude of the worst case difference in t
propagation delay is measured from the 50% level on the falling edge of the V
propagation delay is measured from the 50% level on the rising edge of the V
is the maximum common mode voltage slew rate that can be sustained while maintaining V
1
I-O
I-O
≤5 μA). Each HCPL-772X is proof tested by applying an insulation test voltage ≥4500 Vrms for 1 second (leakage detection
≤ 5 μA.)
2
V
I
PHL
(V)
I
is low and OFF when V
- t
3
PLH
|. %PWD (percent pulse width distortion) is equal to the PWD divided by pulse width.
0 °C
25 °C
85 °C
4
-072X
072X
772X
Option 020
-772X
-772X
-072X
5
I
).
I
Figure 2. Typical input voltage switching thresh-
old vs. input supply voltage.
Symbol
V
R
C
C
T
T
P
is high.
ISO
I-O
jci
jco
PD
I-O
I
2.2
2.1
2.0
1.9
1.8
1.7
1.6
4.5
Min.
3750
3750
5000
4.75
PHL
0 °C
25 °C
85 °C
PD
and/or t
* V
V
DD2
DD1
Typ.
10
0.6
3.0
145
160
140
135
5
12
* f + I
V
(V)
PLH
O
< 0.8 V. The common mode voltage slew rates apply to both rising
that will be seen between units at any given temperature within
DD
Max.
150
5.25
* V
I
I
signal to the 50% level of the rising edge of the V
DD
signal to the 50% level of the falling edge of the V
, where f is switching frequency in MHz.
Units
Vrms
Ω
pF
°C/W
mW
5.5
Figure 3. Typical propagation delays vs. tem-
perature.
O
Test Conditions
RH ≤50%,
t = 1 min.,
T
V
f = 1 MHz
Thermocouple
located at center
underside of package
> 0.8 V
A
I-O
= 25°C
29
27
25
23
21
19
17
15
= 500 Vdc
0
DD2
RMS
10
. CM
for 1 second (leakage detection
20 30
L
T
T
is the maximum common
PLH
PHL
T
40
A
(C)
50
Fig.
60
O
70
O
signal.
Note
8, 9,
10
8
11
signal.
80