HCPL-7720-000E Avago Technologies US Inc., HCPL-7720-000E Datasheet - Page 7

• Manufacturer Part Number: HCPL-7720-000E
• Description: OPTOCOUPLER CMOS 25MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-7720-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 25MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 0.008 us
• Maximum Forward Diode Current: 10 mA
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 25 MBd
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10µA
• Output Voltage: 5V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1689-5

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option 060)
Insulation Resistance at T
† Refer to the front of the optocoupler section of the Isolation and Control Component Designer’s Catalog, under Product Safety Regulations
Note:
These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured
by means of protective circuits.
The surface mount classification is Class A in accordance with CECC 00802.
Absolute Maximum Ratings
Recommended Operating Conditions
7
Description
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b†
Input to Output Test Voltage, Method a†
Highest Allowable Overvoltage†
(Transient Overvoltage, t
Safety Limiting Values
Parameter
Storage Temperature
Ambient Operating Temperature
Supply Voltages
Input Voltage
Output Voltage
Average Output Current
Lead Solder Temperature
Solder Reflow Temperature Profile
Parameter
Ambient Operating Temperature
Supply Voltages
Logic High Input Voltage
Logic Low Input Voltage
Input Signal Rise and Fall Times
V
Test with t
V
for rated mains voltage ≤150 V rms
for rated mains voltage ≤300 V rms
for rated mains voltage ≤450 V rms
t
(Maximum values allowed in the event of a failure,
also see Thermal Derating curve, Figure 11.)
section IEC/EN/DIN EN 60747-5-2, for a detailed description.
m
IORM
IORM
Case Temperature
Input Current
Output Power
= 60 sec, Partial Discharge < 5 pC
x 1.875 = V
x 1.5 = V
m
= 1 sec, Partial Discharge < 5 pC
PR
, Type and Sample Test,
PR
, 100% Production
S
ini
, V
= 10 sec)
10
= 500 V
[1]
Symbol
T
T
V
V
V
I
Symbol
T
V
V
V
t
O
r
A
A
S
I
O
DD1
IH
IL
, t
DD1
f
, V
, V
DD2
DD2
See Solder Reflow Temperature Profile Section
260°C for 10 sec., 1.6 mm below seating plane
Symbol
V
V
V
V
T
I
P
R
S,INPUT
IORM
S
S,OUTPUT
IO
PR
PR
IOTM
Min.
–55
–40
0
–0.5
–0.5
Min.
–40
4.5
2.0
0.0
HCPL-772X
Option 060
55/85/21
2
630
1181
945
6000
175
230
600
≥10
I-IV
I-IV
I-III
9
Max.
125
+85
6.0
V
V
10
Max.
+85
5.5
V
0.8
1.0
DD2
DD1
DD1
+0.5
+0.5
HCPL-072X
Option 060
55/85/21
2
560
1050
840
4000
150
150
600
≥10
I-IV
I-III
Units
°C
°C
Volts
Volts
Volts
mA
Units
°C
V
V
V
ms
9
Figure
Figure
1, 2
Units
V peak
V peak
V peak
V peak
°C
mA
mW
Ω