HCPL-7720-000E Avago Technologies US Inc., HCPL-7720-000E Datasheet - Page 18

• Manufacturer Part Number: HCPL-7720-000E
• Description: OPTOCOUPLER CMOS 25MBD 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-7720-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 25MBd
• Propagation Delay High - Low @ If: 20ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 10 mA
• Maximum Fall Time: 0.008 us
• Maximum Forward Diode Current: 10 mA
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 25 MBd
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• No. Of Channels: 1
• Optocoupler Output Type: Gate Drive
• Input Current: 10µA
• Output Voltage: 5V
• Opto Case Style: DIP
• No. Of Pins: 8
• Common Mode Ratio: 10000
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1689-5

Power Supplies and Bypassing
The recommended DeviceNet application circuit is
shown in Figure 21. Since the HCPL-772X/072X are fully
compatible with CMOS logic level signals, the optocoup-
ler is connected directly to the CAN transceiver. Two by-
pass capacitors (with values between 0.01 and 0.1 μF)
are required and should be located as close as possible
Figure 21. Recommended DeviceNet application circuit.
Implementing PROFIBUS with the HCPL-772X/072X
An acronym for Process Fieldbus, PROFIBUS is essentially
a twisted-pair serial link very similar to RS-485 capable
of achieving high-speed communi cation up to 12 MBd.
As shown in Figure 22, a PROFIBUS Control ler (PBC) es-
tablishes the connec tion of a field automation unit (con-
trol or central processing station) or a field device to
the transmission medium. The PBC consists of the line
transceiver, optical isolation, frame character transmit-
ter/receiver (UART), and the FDL/APP processor with the
interface to the PROFIBUS user.
18
0.01 μF
0.01 μF
TX0
RX0
ISO 5 V
ISO 5 V
GND
1
2
3
4
5
6
7
8
V
V
GND
GND
V
V
DD1
IN
O
DD2
BOUNDARY
HCPL-772x
HCPL-072x
HCPL-772x
HCPL-072x
ISOLATION
GALVANIC
1
2
GND
GND
V
V
DD2
DD1
V
V
IN
O
2
1
8
7
6
5
4
3
2
1
5 V
0.01
0.01
μF
μF
+
0.01 μF
C4
TxD
Rs
82C250
GND
V
5 V
CC
MEDIUM
to the input and output power-supply pins of the HCPL-
772X/072X. For each capacitor, the total lead length be-
tween both ends of the capacitor and the power supply
pins should not exceed 20 mm. The bypass capac itors
are required because of the high-speed digital nature of
the signals inside the optocoupler.
Figure 22. PROFIBUS Controller (PBC).
PBC
CANH
CANL
RXD
REF
(CENTRAL PROCESSING)
+
OPTICAL ISOLATION
CONTROL STATION
USER INTERFACE
PROFIBUS USER:
OR FIELD DEVICE
VREF
TRANSCEIVER
PROCESSOR
REGULATOR
FDL/APP
SWITCHING
LINEAR OR
UART
30 V
D1
0.01 μF
500 V
C1
+
5 V+
4 CAN+
3 SHIELD
2 CAN–
1 V–
R1
1 M