74HC40105N,652 NXP Semiconductors, 74HC40105N,652 Datasheet - Page 24

• Manufacturer Part Number: 74HC40105N,652
• Description: IC FIFO REGISTER 4X16 16DIP
• Manufacturer: NXP Semiconductors
• Series: 74HCr

Specifications of 74HC40105N,652

• Function: Asynchronous
• Memory Size: 64 (4 x 16)
• Data Rate: 25MHz
• Voltage - Supply: 2 V ~ 6 V
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Logic Family: HC
• Logical Function: FIFO Register
• Number Of Elements: 1
• Number Of Bits: 4
• Number Of Inputs: 4
• Number Of Outputs: 4
• High Level Output Current: -7.8mA
• Low Level Output Current: 7.8mA
• Propagation Delay Time: 750ns
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 6V
• Operating Supply Voltage (min): 2V
• Output Type: 3-State
• Polarity: Non-Inverting
• Technology: CMOS
• Frequency (max): 36(Typ)MHz
• Mounting: Through Hole
• Pin Count: 16
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Quiescent Current: 8uA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Access Time: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 74HC40105N; 74HC40105N; 933669660652

Philips Semiconductors
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
DIP
S
The maximum permissible temperature of the solder is
260 C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
R
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 C, contact may be up to 5 seconds.
SO, SSOP and TSSOP
R
Reflow soldering techniques are suitable for all SO, SSOP
and TSSOP packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method.
1998 Jan 23
OLDERING BY DIPPING OR BY WAVE
EPAIRING SOLDERED JOINTS
EFLOW SOLDERING
4-bit x 16-word FIFO register
stg max
). If the
24
Typical reflow temperatures range from 215 to 250 C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 C.
W
Wave soldering can be used for all SO packages. Wave
soldering is not recommended for SSOP and TSSOP
packages, because of the likelihood of solder bridging due
to closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering is used - and cannot be avoided for
SSOP and TSSOP packages - the following conditions
must be observed:
Even with these conditions:
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260 C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 C within
6 seconds. Typical dwell time is 4 seconds at 250 C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
R
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 C.
EPAIRING SOLDERED JOINTS
AVE SOLDERING
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow and must incorporate solder
thieves at the downstream end.
Only consider wave soldering SSOP packages that
have a body width of 4.4 mm, that is
SSOP16 (SOT369-1) or SSOP20 (SOT266-1).
Do not consider wave soldering TSSOP packages
with 48 leads or more, that is TSSOP48 (SOT362-1)
and TSSOP56 (SOT364-1).
74HC/HCT40105
Product specification