XRP7714ILB-0X18-F Exar Corporation, XRP7714ILB-0X18-F Datasheet - Page 11

• Manufacturer Part Number: XRP7714ILB-0X18-F
• Description: IC CTRLR PWM/LDO STP-DWN 40TQFN
• Manufacturer: Exar Corporation
• Series: -r

Specifications of XRP7714ILB-0X18-F

• Topology: Step-Down (Buck) Synchronous (4), Linear (LDO) (1)
• Function: Any Function
• Number Of Outputs: 5
• Frequency - Switching: 1.5MHz
• Voltage/current - Output 1: Controller
• Voltage/current - Output 2: Controller
• Voltage/current - Output 3: Controller
• W/led Driver: No
• W/supervisor: No
• W/sequencer: Yes
• Voltage - Supply: 4.75 V ~ 25 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: *
• Package / Case: *
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1699

FEATURES AND BENEFITS
© 2011 Exar Corporation
• Eliminate temperature and time variations associated
• Tighter
• Easy configuration and re-configuration for different
• Higher integration: Many external circuits can be
• Selectable DPWM frequency and Controller Clock
• A single voltage is needed for regulation [no External
• I
• 6 Configurable GPIO pins, (4 if I
General DPWM Benefits:
Other Benefits:
with passive components in:
− Output set point
− Feedback compensation
− Frequency set point
− Under voltage lock out
− Input voltage measurement
− Gate drive dead time
frequency set point
Vout, Iout, Cout, and Inductor selection by simply
LDO required].
− Communication with a System Controller or other
− Access to modify or read internal registers that
− Packet Error Checking (PEC) on I
be configured in several ways:
− Fault reporting (including OCP, OVP, Temperature,
− Allows a Logic Level interface with other non-digital
changing internal PID coefficients. No need to change
external passives for a new output specification.
handled by monitoring or modifying internal registers
Frequency
2
C interface allows:
Power Management devices for optimized system
function
control or monitor:
− Output Current
− Input and Output Voltage
− Soft-Start/Soft-Stop Time
− ‘Power Good’
− Part Temperature
− Enable/Disable Outputs
− Over Current
− Over Voltage
− Temperature Faults
− Adjusting fault limits and disabling/enabling
Soft-Start in progress, Power Good)
IC’s or as logic inputs to other devices
faults
parameter
tolerances
2
C is in use). Pins can
including
2
C communication
Q
Q
u
u
a
a
operating
d
d
C
C
h
h
a
a
11/29
n
n
n
n
e
e
l
l
• Frequency and Synchronization Capability
• Internal MOSFET Drivers
• PowerArchitect™ Design and Configuration Software:
• Customizing XRP7714 with customer parameters
• Reliability is enhanced via communication with the
• System
• A system process or could also be configured to log
• If customer field service is a possibility for your end
D
D
System Benefits:
− Possible to configure as traditional ‘enable’ pin for
− 2 GPIOs can be dedicated to the I
− Selectable switching frequency between 300kHz and
− Channel to channel phase relationship is a fixed 90
− Main oscillator clock and DPWM clock can be
− ‘Master’, ‘Slave’ and ‘Stand-alone’ Configurations
− Internal FET drivers (3Ω/6Ω) for each Channel
− Built-In Automatic Dead-time adjustment
− 30ns Rise and Fall times
− In its simplest form only VIN, VOUT, and Iout for
− The software calculates configuration register
− Configurations can be saved and/or recalled
− GPIOs can be configured easily and intuitively
− Synchronization configuration can be adjusted
− Interface can be used for real-time debugging and
− Once a configuration is finalized it can be sent to
− Allows parts to be used without I
system controller which can obtain real time data on
an output voltage, input voltage and current.
XRP7714 directly to obtain data or make adjustments
to react to circuit conditions
and analyze operating history, perform diagnostics and
if required, take the supply off-line after making other
system adjustments.
product,
provide additional capabilities for troubleshooting or
aid in future system upgrades.
i
i
g
g
all 4 outputs
required by the customers design
1.5MHz
degrees
synchronized to external sources
are possible
each channel is required.
content based upon customer requirements. PID
coefficients for correct loop response (for automatic
or customized designs) can be generated and sent
to the device.
optimization
EXAR and can reside in pre-programmed parts that
customers can order with an individual part number.
i
i
t
t
a
a
l
l
processors
P
P
parameter
W
W
M
M
S
S
t
t
e
e
reporting
can
p
p
D
D
communicate
o
o
w
w
and
n
n
2
C interface
2
C Interface as
X
X
C
C
R
R
history
o
o
n
P
n
P
Rev. 1.1.6
t
t
with
7
7
r
r
o
o
7
7
would
l
l
1
1
l
l
e
e
the
4
4
r
r