ADSP-BF535PKBZ-300 Analog Devices Inc, ADSP-BF535PKBZ-300 Datasheet - Page 9

• Manufacturer Part Number: ADSP-BF535PKBZ-300
• Description: IC DSP CONTROLLER 16BIT 260 BGA
• Manufacturer: Analog Devices Inc
• Series: Blackfin®r
• Type: Fixed Pointr

Specifications of ADSP-BF535PKBZ-300

• Interface: PCI, SPI, SSP, UART, USB
• Clock Rate: 300MHz
• Non-volatile Memory: External
• On-chip Ram: 308kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.50V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 260-BGA
• No. Of Bits: 32 Bit
• Frequency: 300MHz
• Supply Voltage: 1.5V
• Embedded Interface Type: PCI, SPI, UART
• No. Of I/o's: 16
• Supply Voltage Range: 0.95V To 1.575V, 3.15V To 3.45V
• Package: 260BGA
• Numeric And Arithmetic Format: Floating-Point
• Maximum Speed: 300 MHz
• Device Million Instructions Per Second: 300 MIPS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

DMA controller and interrupt input to minimize processor
polling overhead and to enable asynchronous requests for CPU
attention only when transfer management is required.
The USB device requires an external 48 MHz oscillator. The
value of SCLK must always exceed 48 MHz for proper USB
operation.
Real-Time Clock
The ADSP-BF535 Blackfin processor Real-Time Clock (RTC)
provides a robust set of digital watch features, including current
time, stopwatch, and alarm. The RTC is clocked by a 32.768 kHz
crystal external to the ADSP-BF535 Blackfin processor. The
RTC peripheral has dedicated power supply pins, so that it can
remain powered up and clocked, even when the rest of the
processor is in a low power state. The RTC provides several
programmable interrupt options, including interrupt per second,
minute, or day clock ticks, interrupt on programmable stopwatch
countdown, or interrupt at a programmed alarm time.
The 32.768 kHz input clock frequency is divided down to a 1 Hz
signal by a prescaler. The counter function of the timer consists
of four counters: a 6-bit second counter, a 6-bit minute counter,
a 5-bit hours counter, and an 8-bit day counter.
When enabled, the alarm function generates an interrupt when
the output of the timer matches the programmed value in the
alarm control register. There are two alarms: one is for a time of
day, the second is for a day and time of that day.
The stopwatch function counts down from a programmed value,
with one minute resolution. When the stopwatch is enabled and
the counter underflows, an interrupt is generated.
Like the other peripherals, the RTC can wake up the ADSP-
BF535 Blackfin processor from a low power state upon
generation of any interrupt.
Connect RTC pins XTALI and XTALO with external compo-
nents, as shown in
Watchdog Timer
The ADSP-BF535 Blackfin processor includes a 32-bit timer,
which can be used to implement a software watchdog function.
A software watchdog can improve system availability by forcing
REV. A
SUGGESTED COMPONENTS:
ECLIPTEK EC38J (THROUGH-HOLE PACKAGE)
EPSON MC405 12pF LOAD (SURFACE-MOUNT PACKAGE)
C1 = 22pF
C2 = 22pF
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS. C1 AND C2
SPECIFICATIONS ASSUME BOARD TRACE CAPACITANCE OF 3pF.
Figure 3. External Components for RTC
C1
XTAL1
Figure
3.
X1
C2
XTAL0
–9–
the processor to a known state, via generation of a hardware reset,
non-maskable interrupt (NMI), or general-purpose interrupt, if
the timer expires before being reset by software. The programmer
initializes the count value of the timer, enables the appropriate
interrupt, then enables the timer. Thereafter, the software must
reload the counter before it counts to zero from the programmed
value. This protects the system from remaining in an unknown
state where software, which would normally reset the timer, has
stopped running because of external noise conditions or a
software error.
After a reset, software can determine if the watchdog was the
source of the hardware reset by interrogating a status bit in the
timer control register, which is set only upon a watchdog
generated reset.
The timer is clocked by the system clock (SCLK), at a maximum
frequency of f
Timers
There are four programmable timer units in the ADSP-BF535
Blackfin processor. Three general-purpose timers have an
external pin that can be configured either as a Pulse-Width
Modulator (PWM) or timer output, as an input to clock the
timer, or for measuring pulse widths of external events. Each of
the three general-purpose timer units can be independently pro-
grammed as a PWM, internally or externally clocked timer, or
pulse width counter.
The general-purpose timer units can be used in conjunction with
the UARTs to measure the width of the pulses in the data stream
to provide an autobaud detect function for a serial channel.
The general-purpose timers can generate interrupts to the
processor core providing periodic events for synchronization,
either to the processor clock or to a count of external signals.
In addition to the three general-purpose programmable timers,
a fourth timer is also provided. This extra timer is clocked by the
internal processor clock (CCLK) and is typically used as a system
tick clock for the generation of operating system periodic
interrupts.
Serial Ports (Sports)
The ADSP-BF535 Blackfin processor incorporates two complete
synchronous serial ports (SPORT0 and SPORT1) for serial and
multiprocessor communications. The SPORTs support these
features:
Bidirectional operation—Each SPORT has independent
transmit and receive pins.
Buffered (8-deep) transmit and receive ports—Each port
has a data register for transferring data-words to and from
other processor components and shift registers for shifting
data in and out of the data registers.
Clocking—Each transmit and receive port can either use
an external serial clock or generate its own, in frequencies
ranging from (f
Word length—Each SPORT supports serial data-words
from 3 to 16 bits in length transferred in a format of most
significant bit first or least significant bit first.
SCLK
.
SCLK
/131070) Hz to (f
ADSP-BF535
SCLK
/2) Hz.