ATA5812-PLQW80 Atmel, ATA5812-PLQW80 Datasheet - Page 56

• Manufacturer Part Number: ATA5812-PLQW80
• Description: RF Transceiver RF Data Control Transceiver
• Manufacturer: Atmel

Specifications of ATA5812-PLQW80

• Wireless Frequency: 226 KHz
• Interface Type: 4-Wire SPI
• Noise Figure: 7 dB
• Output Power: 10 dBm
• Operating Supply Voltage: 2.4 V to 5.25 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-48
• Maximum Data Rate: 20 Kbps
• Minimum Operating Temperature: - 40 C
• Modulation: ASK, FSK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.1.7
Figure 11-8. Receiving Mode (TMODE = 1)
56
ATA5811/ATA5812
Receiving Mode
SDO_TMDO
Demod_Out
'0' '0' '0' '0' '0' '0' '0' '0' '0' '1'
Bit-check mode
If the Bit-check was successful for all bits specified by N
receiving mode. To activate a connected microcontroller, the bits VSOUT_EN and CLK_ON in
control register 3 are set to 1. An interrupt is issued at pin IRQ if the control bits T_MODE = 0
and P_MODE = 0.
If the transparent mode is active (T_MODE = 1) and the level on pin CS is low (no data transfer
via the serial interface), the RX data stream is available on pin SDO_TMDO
If the transparent mode is inactive (T_MODE = 0), the received data stream is buffered in the
TX/RX data buffer (see
Manchester and Bi-phase coded signals. It is permanently possible to transfer the data from the
data buffer via the 4-wire serial interface to a microcontroller (see
Buffering of the data stream:
After a successful Bit-check, the transceiver switches from Bit-check mode to receiving mode. In
receiving mode the TX/RX data buffer control logic is active and examines the incoming data
stream. This is done, like in the Bit-check, by subsequent time frame checks where the distance
between two edges is continuously compared to a programmable time window as illustrated in
Figure 11-9 on page
coded signals are valid (T and 2T).
The limits for T are the same as used for the Bit-check. They can be programmed in control
register 5 and 6 (Lim_min, Lim_max).
The limits for 2T are calculated as follows:
Lower limit of 2T:
Upper limit of 2T:
If the result of Lim_min_2T or Lim_max_2T is not an integer value, it will be round up.
Lim_min_2T
T
Lim_max_2T
T
Lim_min_2T
Lim_max_2T
=
=
=
=
Lim_min_2T
Lim_max_2T - 1
Lim_min
Lim_min
57, only two distances between two edges in Manchester and Bi-phase
+
'0'
+
Figure 11-9 on page
Lim_max
Lim_max
'1'
T
XDCLK
'0' '0' '0' '0' '0' '1' '1' '1' '1' '0' '0' '1' '1' '0' '1' '0' '1' '1' '0' '0'
T
Receiving mode
XDCLK
–
+
Lim_max Lim_min
Lim_max Lim_min
–
–
57). The TX/RX data buffer is only usable for
2
2
Bit-check
Figure 10-1 on page
, the transceiver switches to
(Figure
4689F–RKE–08/06
11-8).
46).