AD9220ARS Analog Devices Inc, AD9220ARS Datasheet - Page 24

• Manufacturer Part Number: AD9220ARS
• Description: A/D Converter (A-D) IC
• Manufacturer: Analog Devices Inc

Specifications of AD9220ARS

• Peak Reflow Compatible (260 C): No
• No. Of Bits: 12 Bit
• Leaded Process Compatible: No
• Mounting Type: Surface Mount
• No. Of Channels: 2
• Interface Type: Parallel
• Package / Case: 28-SSOP
• Rohs Status: RoHS non-compliant
• Number Of Bits: 12
• Sampling Rate (per Second): 10M
• Data Interface: Parallel
• Number Of Converters: 7
• Power Dissipation (max): 310mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: Pipelined
• Sample Rate: 10MSPS
• Input Polarity: Unipolar
• Input Type: Voltage
• Rated Input Volt: ±1/±2.5V
• Differential Input: Yes
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 310mW
• Differential Linearity Error: ±0.75LSB
• Integral Nonlinearity Error: ±1.25LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: AD9220-EB - BOARD EVAL FOR AD9220
• Lead Free Status / Rohs Status: Not Compliant

AD9221/AD9223/AD9220
The offset calibration circuitry consists of a DAC, U5 and
the buffer amplifier, U4. The DAC is configured for a bipolar
adjustment span of ± 64 LSB with a 1/2 LSB resolution span
with respect to the AD9221/AD9223/AD9220. Note that both
current outputs of U5 were configured to provide a bipolar
adjustment span. Also, RC is used to decouple the output of
both DACs, U3 and U5, from their respective op amps.
The calibration procedure consists of a two step process. First,
the bipolar offset is calibrated by selecting CH2, the 2.5 V sys-
tem reference, of the analog multiplexer and preloading the DAC,
U5, with a midscale code of 1000 0000. If possible, several
readings of the A/D should be taken and averaged to determine
the required digital offset adjustment code, U5. This averaged
offset code requires an extra bit of resolution since 1 LSB of U5
equates to 1/2 LSB of the AD9221/AD9223/AD9220. The
required offset correction code to U5 can then be determined.
Second, the system gain is calibrated by selecting CH2, a 1.25 V
2.50V
1.25V
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
ADG608
1.25k
U6
0.1 F
U2B
2.5k
OUT
Figure 35. Typical Multichannel Data Acquisition System
0.1 F
0.1 F
2.5k
10 F
U4
2.5k
2.5k
2.5k
VREF(+)
VREF(–)
REF43
U1
162
2.5k
2.5k
DAC08
U3
2.5k
–24–
VREF(+)
VREF(–)
IOUT
IOUT
0.1 F
input that corresponds to –FS of the A/D. Before the value is
read, U4 should be preloaded with a code of 00 (Hex). Several
readings can also be taken and averaged to determine the digital
gain adjustment code to U2A. In this case, 1 LSB of the A/D
corresponds to 1 LSB of U4.
Due to the AD9221/AD9223/AD9220’s excellent INL perfor-
mance, a two-point calibration procedure (i.e., –FS to midscale)
instead of an endpoint calibration procedure was chosen. Also,
since the bipolar offset is insensitive to any gain adjustment (due
to the differential SHA of the A/D), an iterative calibration
process is not required. The temperature stability of the circuit
is enhanced by selecting a dual precision op amp for U2 (e.g.,
OP293) and low temperature drift, thin film resistors. Note that
this application circuit was not built at the release of this data
sheet. Please consult Analog Devices for application assistance
or comments.
1.1k
DAC08
39
39
U5
R
100
C
2
U2A
39
IOUT
IOUT
R
100
C
1.25V
39mV
+5V
R
100
C
SENSE
VREF
VINA
VINB
AD9221/
AD9223/
AD9220
BIT 1 – BIT 12
OTR
REV. E