PIC18F46K20-E/P Microchip Technology, PIC18F46K20-E/P Datasheet - Page 53

• Manufacturer Part Number: PIC18F46K20-E/P
• Description: IC, 8BIT MCU, PIC18F, 64MHZ, DIP-40
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F46K20-E/P

• Controller Family/series: PIC18
• No. Of I/o's: 36
• Eeprom Memory Size: 1024Byte
• Ram Memory Size: 3936Byte
• Cpu Speed: 64MHz
• No. Of Timers: 4
• Core Size: 8 Bit
• Program Memory Size: 32768 Words
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP, ECCP, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPDM164124 - KIT STARTER FOR PIC18F4XK20
• Lead Free Status / Rohs Status: Details

4.2
The MCLR pin provides a method for triggering an
external Reset of the device. A Reset is generated by
holding the pin low. These devices have a noise filter in
the MCLR Reset path which detects and ignores small
pulses.
The MCLR pin is not driven low by any internal Resets,
including the WDT.
In PIC18F2XK20/4XK20 devices, the MCLR input can
be disabled with the MCLRE Configuration bit. When
MCLR is disabled, the pin becomes a digital input. See
Section 10.6 “PORTE, TRISE and LATE Registers”
for more information.
4.3
A Power-on Reset pulse is generated on-chip
whenever V
allows the device to start in the initialized state when
V
To take advantage of the POR circuitry, tie the MCLR
pin through a resistor to V
nal RC components usually needed to create a
Power-on Reset delay. A minimum rise rate for V
specified (parameter D004). For a slow rise time, see
Figure 4-2.
When the device starts normal operation (i.e., exits the
Reset condition), device operating parameters (volt-
age, frequency, temperature, etc.) must be met to
ensure proper operation. If these conditions are not
met, the device must be held in Reset until the operat-
ing conditions are met.
POR events are captured by the POR bit of the RCON
register. The state of the bit is set to ‘0’ whenever a
POR occurs; it does not change for any other Reset
event. POR is not reset to ‘1’ by any hardware event.
To capture multiple events, the user must manually set
the bit to ‘1’ by software following any POR.
 2010 Microchip Technology Inc.
DD
is adequate for operation.
Master Clear (MCLR)
Power-on Reset (POR)
DD
rises above a certain threshold. This
DD
. This will eliminate exter-
DD
is
FIGURE 4-2:
PIC18F2XK20/4XK20
Note 1: External Power-on Reset circuit is required
V
2: 15 k < R < 40 k is recommended to make
3: R1  1 k will limit any current flowing into
DD
D
only if the V
The diode D helps discharge the capacitor
quickly when V
sure that the voltage drop across R does not
violate the device’s electrical specification.
MCLR from external capacitor C, in the event
of MCLR/V
Electrostatic Discharge (ESD) or Electrical
Overstress (EOS).
V
DD
R
C
EXTERNAL POWER-ON
RESET CIRCUIT (FOR
SLOW V
DD
PP
R1
DD
power-up slope is too slow.
pin breakdown, due to
powers down.
DD
MCLR
PIC
POWER-UP)
DS41303G-page 53
®
MCU