PIC16F873-04I/SO Microchip Technology, PIC16F873-04I/SO Datasheet - Page 116

• Manufacturer Part Number: PIC16F873-04I/SO
• Description: IC MCU FLASH 4KX14 EE 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F873-04I/SO

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC16F
• No. Of I/o's: 22
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 192Byte
• Cpu Speed: 4MHz
• No. Of Timers: 3
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 4 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 22
• Interface Type: I2C/SPI/USART
• On-chip Adc: 5-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL309-1073 - ADAPTER 28-SOIC TO 28-SOIC309-1024 - ADAPTER 28-SOIC TO 28-DIP309-1023 - ADAPTER 28-SOIC TO 28-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
7.3
7.4
DS31007A-page 7-4
EEADR
EECON1 and EECON2 Registers
The EEADR register can address up to a maximum of 256 bytes of data EEPROM.
The unused address bits are decoded. This means that these bits must always be '0' to ensure
that the address is in the Data EEPROM memory space.
EECON1 is the control register with five low order bits physically implemented. The upper-three
bits are unimplemented and read as '0's.
Control bits RD and WR initiate read and write, respectively. These bits cannot be cleared, only
set, in software. They are cleared in hardware at completion of the read or write operation. The
inability to clear the WR bit in software prevents the accidental, premature termination of a write
operation.
The WREN bit, when set, will allow a write operation. On power-up, the WREN bit is clear. The
WRERR bit is set when a write operation is interrupted by a MCLR reset or a WDT time-out reset
during normal operation. In these situations, following reset, the user can check the WRERR bit
and rewrite the location. The data and address will be unchanged in the EEDATA and
EEADR registers.
Interrupt flag bit EEIF is set when write is complete. It must be cleared in software.
EECON2 is not a physical register. Reading EECON2 will read all '0's. The EECON2 register is
used exclusively in the Data EEPROM write sequence.
1997 Microchip Technology Inc.