FS2003-UPG7 Equinox Technologies, FS2003-UPG7 Datasheet - Page 70
FS2003-UPG7
Manufacturer Part Number
FS2003-UPG7
Description
UPGRADE FS2003 JTAG ISP AVR MCU
Manufacturer
Equinox Technologies
Type
Upgrade Kitr
Datasheet
1.FS2003US.pdf
(78 pages)
Specifications of FS2003-UPG7
Mfg Application Notes
SPI and JTAG (ISP), Appl Note
For Use With/related Products
FS2003
Other names
483-1009
- Current page: 70 of 78
- Download datasheet (3Mb)
4.6 J6(b) - Equinox 10-way Header (ATtiny11/12/15 HV Interface)
This connection method is suitable for interfacing the programmer to a Target System which features
the following:
The connector supports programming of the Atmel ATtiny11/12/15 microcontrollers in ‘High Voltage
Serial Programming Mode’. This mode requires that a +12.0V Vpp voltage is applied to the RESET
pin of the target device in order to enter programming mode.
To implement this connection, simply plug the 10-way ISP cable into the Programmer J6 header and
plug the other end of the cable into the matching header on the Target System. Please ensure that
you have made the correct connections from the ISP Header to your Target Device.
Pin
No
1
2
3
FS2003 ISP Programmer - User Guide V1.08 – 1
•
•
•
Programmer
Pin name
PROG_VCC
PROG_SPARE
PROG_TSCK2
Equinox 10-way IDC ISP Header
An Atmel ATtiny microcontroller eg. ATtiny11/12/15
Suitable connections to implement ‘High Voltage Serial Programming Mode’.
Programmer
Input /
Output
P
-
O
Figure 4.6.1 – Equinox 10-way IDC Header (J8) viewed from above
Warning!
Connect to
pin on
Target Device
TARGET_VCC
No connect
XTAL1
3. It is possible for +12V to be output on pin 10 of this
4. Connecting to the wrong ISP Header may cause
st
August 08
connector when programming ATtiny11/12/15 devices.
catastrophic damage to the Programmer & Target
System
Description
Target VCC
This pin should be connected to
the Target System Vcc. This
voltage could be used to power
the programmer depending on the
settings of the power
switch/jumper on the programmer.
Spare Programmer I/O pin
This pin is currently a I/O spare pin
which is not used during SPI
programming. In order to use this
pin, the pin state must be setup in
the EQTools <Pre-programming
State Machine> tab.
SCK2 Clock Output
This output pin is used to supply
an external clock signal (SCK2) to
the target microcontroller.
67
Related parts for FS2003-UPG7
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROGRAMMER PORTABLE HI-SPEED ISP
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
U[GRADE FS2003 ATC SERIAL CONTRO
Manufacturer:
Equinox Technologies
Part Number:
Description:
UPGRADE FS2003 ATMEL AT91SAM7
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
PROGRAMMER, ISP
Manufacturer:
Equinox Technologies
Datasheet:
Part Number:
Description:
TRANSF 10VAC .24A SPLIT PACK
Manufacturer:
Triad Magnetics
Datasheet:
Part Number:
Description:
TRANSF 10VAC .6A SPLIT PACK
Manufacturer:
Triad Magnetics
Datasheet:
Part Number:
Description:
TRANSF 10VAC 1.2A SPLIT PACK
Manufacturer:
Triad Magnetics
Datasheet:
Part Number:
Description:
TRANSF 10VAC .11A SPLIT PACK
Manufacturer:
Triad Magnetics
Datasheet:
Part Number:
Description:
RES 10 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES .50 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES 1.0 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES 5.0 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES 25 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES 2.5K OHM 20W 5% SILICON PCB
Manufacturer:
Huntington Electric Inc.
Datasheet:
Part Number:
Description:
RES 250 OHM 20W 5% SILICONE PCB
Manufacturer:
Huntington Electric Inc.
Datasheet: