KS8695P-EVAL Micrel Inc, KS8695P-EVAL Datasheet - Page 24

• Manufacturer Part Number: KS8695P-EVAL
• Description: BOARD EVAL EXPERIMENT KS8695P
• Manufacturer: Micrel Inc

Specifications of KS8695P-EVAL

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 576-1002

August 2005
LAN Ethernet Physical Interface Pins
PHY LED Drivers
Note:
1. I = Input.
KS8695P
O = Output.
O/I = Output in normal mode; input pin during reset.
C17
D17
C16
D16
E15
E14
B17
E17
B16
E16
Pin
Pin
H1
H2
H3
H4
K1
K2
K3
K4
F1
F3
J1
L1
J2
L2
J3
L3
J4
L4
LANFXSD1
LANRXM1
LANRXM2
LANRXM3
LANRXM4
LANTXM1
LANTXM2
LANTXM3
LANTXM4
LANTXP1
LANTXP2
LANTXP3
LANTXP4
LANRXP1
LANRXP2
LANRXP3
LANRXP4
B0SIZE0
B0SIZE1
WLED0/
WLED1/
L1LED0
L2LED0
L3LED0
L4LED0
L1LED1
L2LED1
L3LED1
L4LED1
Name
Name
ISET
I/O Type
I/O Type
O/I
O/I
O
O
O
O
I
I
I
I
(1)
(1)
Description
LAN Port[4:1] PHY transmit signal + (differential).
LAN Port[4:1] PHY transmit signal – (differential).
LAN Port[4:1] PHY receive signal + (differential).
LAN Port[4:1] PHY receive signal – (differential).
Set PHY transmit output current. Connect to ground through a 3.01kΩ 1% resistor.
LAN fiber signal detect. Signal detect input when the LAN1 port is operated in
100BASE-FX 100Mb fiber mode. See Application Note 107.
Description
Normal Mode: WAN LED indicator 0. Programmable via WAN misc. Control register
bits [2:0].
‘000’ = Speed; ‘001’ = Link; ‘010’ = Full/half duplex; ‘011’ = Collision;
‘100’ = TX/RX activity; ‘101’ = Full-duplex collision; ‘110’ = Link/Activity.
During reset: Bank 0 Data Access Size. Bank 0 is used for the boot program.
B0SIZE[1:0] are used to specify the size of the bank 0 data bus width as follows:
‘01’ = one byte, ‘10’ = half-word, ‘11’ = one word, and ‘00’ = reserved.
Normal Mode: WAN LED indicator 1. Programmable via WAN Misc. Control register
bits [6:4].
‘000’ = Speed; ‘001’= Link; ‘010’ = Full/half duplex; ‘011’ = Collision;
‘100’ = TX/RX activity; ‘101’ = Full-duplex collision; ‘110’ = Link/Activity.
During reset: Bank 0 data access size. Bank 0 is used for the boot program.
B0SIZE[1:0] are used to specify the size of the bank 0 data bus width as follows:
‘01’ = one byte, ‘10’ = half-word, ‘11’ = one word, and ‘00’ = reserved.
LAN Port[4:1] LED indicator 0. Programmable via switch control 0 register bits
[27:25].
‘000’ = Speed; ‘001’ = Link; ‘010’ = Full/half duplex; ‘011’ = Collision;
'100’ = TX/RX activity; ‘101’ = Full-duplex collision; ‘110’ = Link/Activity.
LAN Port[4:1] LED indicator 1. Programmable via switch control 0 register bits
[24:22].
‘000’ = Speed; ‘001’ = Link; ‘010’ = Full/half duplex; ‘011’ = Collision;
‘100’ = TX/RX activity; ‘101’ = Full-duplex collision; ‘110’ = Link/Activity.
24
M9999-081805
Micrel