STEVAL-MKI062V2 STMicroelectronics, STEVAL-MKI062V2 Datasheet - Page 8

• Manufacturer Part Number: STEVAL-MKI062V2
• Description: BOARD EVAL FOR MEMS SENSORS
• Manufacturer: STMicroelectronics
• Series: iNEMOr

Specifications of STEVAL-MKI062V2

• Design Resources: STEVAL-MKI062V2 Gerber Files STEVAL-MKI062V2 Schematic STEVAL-MKI062V2 Bill of Materials
• Sensor Type: Accelerometer, Gyroscope, Magnetometer, Pressure, Temperature
• Sensing Range: ±2g,4g,8g; 300 ~ 1100mbar; 300°/sec; -55 ~125°C
• Interface: I²C, USB
• Sensitivity: Multiple
• Voltage - Supply: 5V, USB
• Embedded: Yes, MCU, 32-Bit
• Utilized Ic / Part: LPR430AL, LY330ALH, LSM303DLH, LPS001DL, STM32F103RE, STLM75
• Interface Type: USB, CAN, I2C
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Silicon Manufacturer: STMicroelectronics
• Kit Application Type: Sensor
• Application Sub Type: MEMS Device
• Silicon Family Name: INEMO
• Kit Contents: MicroSD Card Slot, COM Connector, Reset Button,
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: STM32F103RE
• Other names: 497-10508

iNEMO suite
2
8/18
iNEMO suite
The iNEMO suite application allows the user to work both with the iNEMO V1 and iNEMO
V2 platform. At the startup of the application, the kit selector window appears, to choose the
platform used
The iNEMO suite application is based on the software development kit (SDK)
iNEMO_SDK.dll (for STEVAL-MKI062V1) and iNEMO2_SDK.dll (for STEVAL-MKI062V2).
Only for the STEVAL-MKI062V2 is the iNEMO suite application also a TCP/IP server for
external/remote demo applications; when the server starts, in the log bar a message shows
the availability of the server. Each client may be connected to the server on port
31001(default) to receive data from the device through the iNEMO suite (server).
Every time a client is connected to the server the log bar shows the IP address of the client
just connected.
Each demo (client) could elaborate and show these data. (The structure of the data sample
sent to all clients is the FrameData_t defined in the iNEMO2_SDK.h).
The TCP/IP server may be enabled/disabled from the Tools->Communication->Settings
menu (its state is shown on the status bar below). From this dialog box, the user can change
the communication port (default 31001). Pay close attention to this information in order to
avoid a communication block from an installed firewall.
To run the INEMO suite:
1.
2.
3.
4.
It is preferable to connect the iNEMO board to a free USB port before launching the GUI. In
this way, the GUI directly finds the COM port into which the board is plugged.
To change COM port press the “New” button on the toolbar or from the menu File/New and
the kit selector dialog appears.
Click on Start > All Programs > STMicroelectronics > iNEMO Suite > iNEMO Suite
Application
Launch the program iNEMO software tool (Goldfish Icon)
At first, the “Kit Selector” window appears
Check that the serial port number is correct (see
button and choose the right COM port.
(Figure
6).
Doc ID 18054 Rev 1
(Figure
Figure
6). Select STEVAL-MKI062V2
5). Otherwise click the refresh
UM1010