Z8FMC160100KIT Zilog, Z8FMC160100KIT Datasheet - Page 105
Z8FMC160100KIT
Manufacturer Part Number
Z8FMC160100KIT
Description
KIT DEV FOR Z8 ENCORE Z8FMC16100
Manufacturer
Zilog
Series
Z8 Encore! MC™r
Datasheets
1.Z8FMC160100KIT.pdf
(7 pages)
2.Z8FMC160100KIT.pdf
(383 pages)
3.Z8FMC160100KIT.pdf
(20 pages)
Specifications of Z8FMC160100KIT
Main Purpose
Power Management, Motor Control
Embedded
Yes, MCU, 8-Bit
Utilized Ic / Part
Z8FMC16100
Primary Attributes
3-Ph DC Motors
Secondary Attributes
Graphic User Interface
Processor To Be Evaluated
Z8FMC16100
Data Bus Width
8 bit
Interface Type
USB
For Use With
269-4664 - KIT ACC OPTO-ISO USB SMART CABLE269-4661 - KIT ACC ETHERNET SMART CABLE269-4539 - KIT ACCESSORY USB SMART CABLE
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3639
- Current page: 105 of 383
- Download datasheet (5Mb)
PS024613-0910
TRIGGERED ONE-SHOT Mode Timeout Period (s) =
Note:
2. Write to the Timer High and Low Byte registers to set the starting count value.
3. Write to the Timer Reload High and Low Byte registers to set the reload value.
4. If appropriate, enable the timer interrupt and set the timer interrupt priority by writing
5. If using the Timer Output function, configure the associated GPIO port pin for the
6. Write to the Timer Control 1 register to enable the timer. Counting does not start until
The timer period is calculated by the following equation (Start Value = 1):
The one-shot delay from input trigger to output includes the above-defined timeout period,
plus an additional delay of 2–3 system clock cycles, due to the synchronization of the input
trigger.
CONTINUOUS Mode
In CONTINUOUS mode, the timer counts up to the 16-bit reload value stored in the Timer
Reload High and Low Byte registers. After reaching the reload value, the timer generates
an interrupt, the count value in the Timer High and Low Byte registers is reset to
and counting resumes. Also, if the Timer Output alternate function is enabled, the Timer
Output pin changes state (from Low to High or High to Low) after timer reload.
Follow the steps below to configure a timer for CONTINUOUS mode and initiate the
count:
1. Write to the Timer Control registers to:
(d) If using the Timer Output alternate function, set the initial output level (High or
(e) Set the INTERRUPT mode.
to the relevant interrupt registers.
Timer Output alternate function.
the appropriate input transition occurs.
(a) Disable the timer.
(b) Configure the timer for CONTINUOUS mode.
(c) Set the prescale value.
(d) If using the Timer Output alternate function, set the initial output level (High or
Low) via the
Low) through
TPOL
TPOL
bit.
.
(Reload Value – Start Value + 1) x Prescaler
System Clock Frequency (Hz)
Z8FMC16100 Series Flash MCU
Product Specification
Timer Operating Modes
0001h
,
93
Related parts for Z8FMC160100KIT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: