FOD3150S Fairchild Optoelectronics Group, FOD3150S Datasheet
FOD3150S
Specifications of FOD3150S
Available stocks
Related parts for FOD3150S
FOD3150S Summary of contents
Page 1
FOD3150 High Noise Immunity, 1.0A Output Current, Gate Drive Optocoupler Features High noise immunity characterized by 20kV/µs minimum common mode rejection Use of P-channel MOSFETs at output stage enables output voltage swing close to the supply rail Wide supply voltage ...
Page 2
Truth Table V – V “Positive Going” LED (Turn-on) Off 0V to 30V 11V On 11V to 13.5V On 13.5V to 30V Pin Definitions Pin # Name Anode 3 Cathode 4 NC ...
Page 3
Safety and Insulation Ratings As per IEC 60747-5-2. This optocoupler is suitable for “safe electrical insulation” only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits. Symbol Installation Classifications per DIN ...
Page 4
Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure ...
Page 5
Electrical Characteristics Apply over all recommended conditions, typical value is measured at V unless otherwise specified. Symbol Parameter V Input Forward Voltage Temperature Coefficient Forward Voltage BV Input Reverse Breakdown R Voltage ...
Page 6
Switching Characteristics Apply over all recommended conditions, typical value is measured at V unless otherwise specified. Symbol Parameter t Propagation Delay Time to Logic PHL Low Output t Propagation Delay Time to Logic PLH High Output PWD Pulse Width Distortion, ...
Page 7
Typical Performance Curves Fig. 1 Output High Voltage Drop vs. Output High Current 0.5 0.0 -0.5 -1 -1.5 -2.0 0.00 0.25 0.50 0. OUTPUT HIGH CURRENT (A) OH Fig. 3 Output Low Voltage vs. Output Low ...
Page 8
Typical Performance Curves Fig. 7 Low to High Input Current Threshold vs. Ambient Temperature 4 15V to 30V 3.5 Output = Open 3.0 2.5 2.0 1.5 1.0 -40 - ...
Page 9
Typical Performance Curves Fig. 13 Transfer Characteristics 30V – FORWARD LED CURRENT (mA) F ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. ...
Page 10
Test Circuit Pulse Generator PW = 4.99ms Period = 5ms Pulse- OUT LED-IFmon Test Conditions: Frequency = 200Hz Duty Cycle = 99. 15V to 30V -3.0V to 0.8V ...
Page 11
Test Circuit (Continued 16mA F ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. 1.0 0 Figure 22. V Test Circuit 0 ...
Page 12
Test Circuit (Continued 16mA 0.8V – F ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. 1.0 0 Figure 24. I Test Circuit CCH ...
Page 13
Test Circuit (Continued 0.8V – 10mA F ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. 1.0 0 Figure 26. I Test Circuit FLH 1 ...
Page 14
Test Circuit (Continued) + – Probe F = 10kHz OUT Figure 29 – ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. 1.0 ...
Page 15
Package Dimensions Through Hole PIN 1 ID 0.270 (6.86) 0.250 (6.35 0.390 (9.91) 0.370 (9.40) 0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN 0.200 (5.08) 0.140 (3.55) 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) ...
Page 16
... SMT 8-Pin (Lead Bend) FOD3150V DIP 8-Pin, IEC60747-5-2 option (Pending approval) FOD3150SV SMT 8-Pin (Lead Bend), IEC60747-5-2 option (Pending approval) FOD3150SDV SMT 8-Pin (Lead Bend), IEC60747-5-2 option (Pending approval) FOD3150T DIP 8-Pin, 0.4” Lead Spacing FOD3150TV DIP 8-Pin, 0.4” Lead Spacing , IEC60747-5-2 option ...
Page 17
Carrier Tape Specifications Symbol ©2008 Fairchild Semiconductor Corporation FOD3150 Rev. 1.0 ...
Page 18
Reflow Profile 300 250 200 150 100 • Peak reflow temperature: 260 C (package surface temperature) • Time of temperature higher than 183 C for 160 seconds or less • One time soldering reflow is recommended ©2008 ...
Page 19
TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its gl o bal subsidiaries, and is not intended exhaustive list of all such trademarks. AccuPower™ F-PFS™ FRFET Auto-SPM™ Build it ...