ISL62884CIRTZ Intersil, ISL62884CIRTZ Datasheet - Page 3
![IC REG PWM SGL PHASE 28TQFN](/photos/28/21/282175/28-tqfn_l28_sml.jpg)
ISL62884CIRTZ
Manufacturer Part Number
ISL62884CIRTZ
Description
IC REG PWM SGL PHASE 28TQFN
Manufacturer
Intersil
Datasheet
1.ISL62884CHRTZ.pdf
(30 pages)
Specifications of ISL62884CIRTZ
Applications
Controller, Intel IMVP-6
Voltage - Input
4.5 ~ 25 V
Number Of Outputs
1
Voltage - Output
0.0125 ~ 1.5 V
Operating Temperature
-40°C ~ 100°C
Mounting Type
Surface Mount
Package / Case
28-VQFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL62884CIRTZ
Manufacturer:
NA
Quantity:
20 000
Pin Function Description
20 thru 26
NUMBER
9, 10
PIN
Pad
11
12
13
14
15
16
17
18
19
27
28
1
2
3
4
5
6
7
8
ISUM- and
DPRSLPVR
VID0 thru
CLK_EN#
DPRSTP#
SYMBOL
PGOOD
VR_ON
ISUM+
UGATE
PHASE
RBIAS
LGATE
COMP
BOOT
VSEN
VSSP
VCCP
VID6
VDD
RTN
VIN
VW
PD
FB
Open drain output to enable system PLL clock. It goes low 13 switching cycles after V
10% of V
Power-Good open-drain output indicating when the regulator is able to supply regulated voltage.
Pull-up externally with a 680Ω resistor to VCCP or 1.9kΩ to 3.3V.
application and a 47kΩ resistor sets the controller for GPU core application.
A resistor from this pin to COMP programs the switching frequency (8kΩ gives approximately
300kHz).
This pin is the output of the error amplifier. Also, a resistor across this pin and GND adjusts the
overcurrent threshold.
This pin is the inverting input of the error amplifier.
Remote core voltage sense input. Connect to microprocessor die.
Remote voltage sensing return. Connect to ground at microprocessor die.
Droop current sense input.
5V bias power.
Power stage supply voltage, used for feed-forward.
A mode signal from the CPU. Combined with the DPRSLPVR signal, it determines the operational
mode of the controller.
Connect an MLCC capacitor across the BOOT and the PHASE pin. The boot capacitor is charged
through an internal boot diode connected from the VCCP pin to the BOOT pin, each time the PHASE
pin drops below VCCP minus the voltage dropped across the internal boot diode.
Output of the high-side MOSFET gate driver. Connect the UGATE pin to the gate of the high-side
MOSFET.
Current return path for the high-side MOSFET gate driver. Connect the PHASE pin to the node
consisting of the high-side MOSFET source, the low-side MOSFET drain, and the output inductor.
Current return path for the low-side MOSFET gate driver. Connect the VSSP pin to the source of the
low-side MOSFET through a low impedance path, preferably in parallel with the traces connecting
the LGATE pins to the gates of the low-side MOSFET.
Output of the low-side MOSFET gate driver. Connect the LGATE1 pin to the gate of the Phase-1
low-side MOSFET.
Input voltage bias for the internal gate drivers. Connect +5V to the VCCP pin. Decouple with at
least 1µF of an MLCC capacitor to the VSSP pin.
VID input with VID0 = LSB and VID6 = MSB.
Voltage regulator enable input. A high level logic signal on this pin enables the regulator.
Deeper sleep enable signal. A high level logic signal on this pin indicates that the microprocessor
is in deeper sleep mode. It also programs the output voltage slew rate at 10mV/µs for
DPRSLPVR = 0 and 2.5mV/µs for DPRSLPVR = 1.
The bottom pad is electrically connected to the GND pin inside the IC. It should also be used as the
thermal pad for heat removal.
3
A resistor to GND sets internal current reference. A 147kΩ resistor sets the controller for CPU core
BOOT
.
ISL62884C
ISL62884C
DESCRIPTION
CORE
March 16, 2010
is within
FN7591.0