C8051F314R Silicon Labs, C8051F314R Datasheet - Page 135

no-image

C8051F314R

Manufacturer Part Number
C8051F314R
Description
8-bit Microcontrollers - MCU 8KB 10ADC
Manufacturer
Silicon Labs
Datasheet

Specifications of C8051F314R

Product Category
8-bit Microcontrollers - MCU
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
25 MHz
Program Memory Size
8 KB
Data Ram Size
1.25 KB
On-chip Adc
Yes
Operating Supply Voltage
2.7 V to 3.6 V
Package / Case
LQFP-32
Mounting Style
SMD/SMT
A/d Bit Size
10 bit
A/d Channels Available
17
Data Rom Size
128 B
Interface Type
I2C, SMBus, SPI, UART
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Number Of Programmable I/os
29
Number Of Timers
5
On-chip Dac
No
Processor Series
C8051
Program Memory Type
Flash
Factory Pack Quantity
500
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
13.3. General Purpose Port I/O
Port pins that remain unassigned by the Crossbar and are not used by analog peripherals can be used for
general purpose I/O. Ports3-0 are accessed through corresponding special function registers (SFRs) that
are both byte addressable and bit addressable. When writing to a Port, the value written to the SFR is
latched to maintain the output data value at each pin. When reading, the logic levels of the Port's input pins
are returned regardless of the XBRn settings (i.e., even when the pin is assigned to another signal by the
Crossbar, the Port register can always read its corresponding Port I/O pin). The exception to this is the
execution of the read-modify-write instructions. The read-modify-write instructions when operating on a
Port SFR are the following: ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ and MOV, CLR or SET, when the
destination is an individual bit in a Port SFR. For these instructions, the value of the register (not the pin) is
read, modified, and written back to the SFR.
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bits2–0: PCA0ME: PCA Module I/O Enable Bits.
WEAKPUD XBARE
R/W
Bit7
WEAKPUD: Port I/O Weak Pullup Disable.
0: Weak Pullups enabled (except for Ports whose I/O are configured as analog input).
1: Weak Pullups disabled.
XBARE: Crossbar Enable.
0: Crossbar disabled.
1: Crossbar enabled.
T1E: T1 Enable
0: T1 unavailable at Port pin.
1: T1 routed to Port pin.
T0E: T0 Enable
0: T0 unavailable at Port pin.
1: T0 routed to Port pin.
ECIE: PCA0 External Counter Input Enable
0: ECI unavailable at Port pin.
1: ECI routed to Port pin.
000: All PCA I/O unavailable at Port pins.
001: CEX0 routed to Port pin.
010: CEX0, CEX1 routed to Port pins.
011: CEX0, CEX1, CEX2 routed to Port pins.
100: CEX0, CEX1, CEX2, CEX3 routed to Port pins.
101: CEX0, CEX1, CEX2, CEX3, CEX4 routed to Port pins.
SFR Definition 13.2. XBR1: Port I/O Crossbar Register 1
R/W
Bit6
T1E
R/W
Bit5
T0E
R/W
Bit4
Rev. 1.7
ECIE
R/W
Bit3
C8051F310/1/2/3/4/5/6/7
R/W
Bit2
PCA0ME
R/W
Bit1
R/W
Bit0
SFR Address:
00000000
Reset Value
0xE2
135

Related parts for C8051F314R