C8051F347-GMR Silicon Labs, C8051F347-GMR Datasheet - Page 206
C8051F347-GMR
Manufacturer Part Number
C8051F347-GMR
Description
8-bit Microcontrollers - MCU 25 MIPS 32KB 10 ADC
Manufacturer
Silicon Labs
Datasheet
1.C8051F349-GMR.pdf
(276 pages)
Specifications of C8051F347-GMR
Rohs
yes
Core
8051
Data Bus Width
8 bit
Processor Series
C8051
- Current page: 206 of 276
- Download datasheet (2Mb)
C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
18.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 18.2), which is not
user-accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud
rates. The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
Timer with Auto-Reload” on page 237
occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of six
sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, the external oscillator clock / 8, or an exter-
nal input T1. For any given Timer 1 clock source, the UART0 baud rate is determined by Equation 18.1.
Where T1
value). Timer 1 clock frequency is selected as described in
reference for typical baud rates using the internal oscillator is given in Table 18.1. Note that the internal
oscillator may still generate the system clock if an external oscillator is driving Timer 1.
18.2. Operational Modes
UART0 provides standard asynchronous, full duplex communication. The UART mode (8-bit or 9-bit) is
selected by the S0MODE bit (SCON0.7). Typical UART connection options are shown below.
206
CLK
is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
Detected
Start
Figure 18.2. UART0 Baud Rate Logic
RX Timer
Equation 18.1. UART0 Baud Rate
UartBaudRate
Timer 1
TH1
TL1
). The Timer 1 reload value should be set so that overflows will
Overflow
Overflow
Rev. 1.3
=
------------------------------ -
256 T1H
T1
–
Section “21. Timers” on page 235
CLK
Section “21.1.3. Mode 2: 8-bit Counter/
2
2
UART
1
-- -
2
RX Clock
TX Clock
. A quick
Related parts for C8051F347-GMR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVALUATION FOR CP2102
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2103 USB TO UART
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT EVAL FOR CP2201 ETH CTRLR
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DAUGHTER CARD CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT STARTER CAP TOUCH SENSE
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F320/F321
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEVKIT-F120/21/22/23/24/25/26/27
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F310/F311
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F220/221/226/230/231/236
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT F300/301/302/303/304/305
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR C8051F330/F331
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F005/006/007
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
DEV KIT FOR F020/F021/F022/F023
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F34X
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
KIT DEV FOR C8051F41X
Manufacturer:
Silicon Laboratories Inc
Datasheet: