LPC1114FHN33/203,5 NXP Semiconductors, LPC1114FHN33/203,5 Datasheet - Page 218
LPC1114FHN33/203,5
Manufacturer Part Number
LPC1114FHN33/203,5
Description
ARM Microcontrollers - MCU Cortex-M0 32 kB Fl 8 kB SRAM
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1113FHN333035.pdf
(538 pages)
Specifications of LPC1114FHN33/203,5
Rohs
yes
Core
ARM Cortex M0
Processor Series
LPC1114
Data Bus Width
32 bit
Maximum Clock Frequency
50 MHz
Program Memory Size
32 KB
Data Ram Size
8 KB
On-chip Adc
Yes
Operating Supply Voltage
1.8 V to 3.6 V
Operating Temperature Range
- 65 C to + 150 C
Package / Case
HVQFN-33
Mounting Style
SMD/SMT
Factory Pack Quantity
260
- Current page: 218 of 538
- Download datasheet (5Mb)
NXP Semiconductors
14.5 Pin description
UM10398
User manual
The LPC111x/LPC11Cxx has two SPI/Synchronous Serial Port controllers.
Table 205. SPI pin descriptions
Remark: The SCK0 function is multiplexed to three different pin locations (two locations
on the HVQFN package). Use the IOCON_LOC register (see
physical location for the SCK0 function in addition to selecting the function in the IOCON
registers. The SCK1 pin is not multiplexed.
Pin
name
SCK0/1
SSEL0/1 I/O
MISO0/1 I/O
MOSI0/1 I/O
Type
I/O
All information provided in this document is subject to legal disclaimers.
Interface pin
name/function
SPI
SCK
SSEL FS
MISO DR(M)
MOSI DX(M)
Rev. 12 — 24 September 2012
SSI
CLK
DX(S)
DR(S)
Microwire
SK
CS
SI(M)
SO(S)
SO(M)
SI(S)
Chapter 14: LPC111x/LPC11Cxx SPI0/1 with SSP
Pin description
Serial Clock. SCK/CLK/SK is a clock signal used
to synchronize the transfer of data. It is driven by
the master and received by the slave. When
SPI/SSP interface is used, the clock is
programmable to be active-high or active-low,
otherwise it is always active-high. SCK only
switches during a data transfer. Any other time, the
SPI/SSP interface either holds it in its inactive state
or does not drive it (leaves it in high-impedance
state).
Frame Sync/Slave Select. When the SPI/SSP
interface is a bus master, it drives this signal to an
active state before the start of serial data and then
releases it to an inactive state after the data has
been sent.The active state of this signal can be
high or low depending upon the selected bus and
mode. When the SPI/SSP interface is a bus slave,
this signal qualifies the presence of data from the
Master according to the protocol in use.
When there is just one bus master and one bus
slave, the Frame Sync or Slave Select signal from
the Master can be connected directly to the slave’s
corresponding input. When there is more than one
slave on the bus, further qualification of their Frame
Select/Slave Select inputs will typically be
necessary to prevent more than one slave from
responding to a transfer.
Master In Slave Out. The MISO signal transfers
serial data from the slave to the master. When the
SPI/SSP is a slave, serial data is output on this
signal. When the SPI/SSP is a master, it clocks in
serial data from this signal. When the SPI/SSP is a
slave and is not selected by FS/SSEL, it does not
drive this signal (leaves it in high-impedance state).
Master Out Slave In. The MOSI signal transfers
serial data from the master to the slave. When the
SPI/SSP is a master, it outputs serial data on this
signal. When the SPI/SSP is a slave, it clocks in
serial data from this signal.
Section
UM10398
7.4) to select a
© NXP B.V. 2012. All rights reserved.
218 of 538
Related parts for LPC1114FHN33/203,5
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: