XR16C850CJ EXAR [Exar Corporation], XR16C850CJ Datasheet - Page 32

• Manufacturer Part Number: XR16C850CJ
• Manufacturer: EXAR [Exar Corporation]

MCR BIT-6:
Logic 0 = Enable Modem receive and transmit input/
output interface. (normal default condition)
Logic 1 = Enable infrared IrDA receive and transmit
inputs/outputs. While in this mode, the TX/RX output/
Inputs are routed to the infrared encoder/decoder. The
data input and output levels will conform to the IrDA
infrared interface requirement. As such, while in this
mode the infrared TX output will be a logic 0 during idle
data conditions. Care must be taken into consideration
in the design not to over heat the IR LED during powerup
initialization state while TX output is still at logic 1.
Procedure to enable the IR encoder and decoder functions during
initialization routine.
MCR BIT-7:
This bit overrides the CLKSEL pin selection.
Logic 0 = Divide by one. The input clock (crystal or
external) is divided by sixteen and then presented to the
Programmable Baud Rate Generator (BGR) without
further modification, i.e., divide by one. (normal, default
condition)
Logic 1 = Divide by four. The divide by one clock
described in MCR bit-7 equals a logic 0, is further divided
by four (also see Programmable Baud Rate Generator
section).
Line Status Register (LSR)
This register provides the status of data transfers
between the 850 and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register or FIFO.
(normal default condition)
Logic 1 = Data has been received and is saved in the
receive holding register or FIFO.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred in
the receive shift register. This happens when additional
data arrives while the FIFO is full. In this case the
Write LCR with “BF” hex
Set EFR bit-4 to logic 1
Write LCR with op. values ; set operating parameters
Set MCR bit-6 to logic 1
XR16C850
Rev. 1.20
; enable IR mode, TX pin goes logic 0
; enable enhanced function bits
; access to EFR “shadow” register
32
previous data in the shift register is overwritten. Note
that under this condition the data byte in the receive shift
register is not transfer into the FIFO, therefore the data
in the FIFO is not corrupted by the error.
LSR BIT-2:
Logic 0 = No parity error (normal default condition)
Logic 1 = Parity error. The receive character does not
have correct parity information and is suspect. In the
FIFO mode, this error is associated with the character
at the top of the FIFO.
LSR BIT-3:
Logic 0 = No framing error (normal default condition).
Logic 1 = Framing error. The receive character did not
have a valid stop bit(s). In the FIFO mode this error is
associated with the character at the top of the FIFO.
LSR BIT-4:
Logic 0 = No break condition (normal default condition)
Logic 1 = The receiver received a break signal (RX was
a logic 0 for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO.
LSR BIT-5:
This bit is the Transmit Holding Register Empty indica-
tor. This bit indicates that the UART is ready to accept
a new character for transmission. In addition, this bit
causes the UART to issue an interrupt to CPU when the
THR interrupt enable is set. The THR bit is set to a logic
1 when a character is transferred from the transmit
holding register into the transmitter shift register. The bit
is reset to logic 0 concurrently with the loading of the
transmitter holding register by the CPU. In the FIFO
mode this bit is set when the transmit FIFO is empty;
it is cleared when at least 1 byte is written to the transmit
FIFO.
LSR BIT-6:
This bit is the Transmit Empty indicator. This bit is set
to a logic 1 whenever the transmit holding register and
the transmit shift register are both empty. It is reset to
logic 0 whenever either the THR or TSR contains a data
character. In the FIFO mode this bit is set to one
whenever the transmit FIFO and transmit shift register
are both empty.
LSR BIT-7:
Logic 0 = No Error (normal default condition)