P82B96TD/S900 NXP [NXP Semiconductors], P82B96TD/S900 Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
P82B96TD/S900
Manufacturer Part Number
P82B96TD/S900
Description
Dual bidirectional bus buffer
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.P82B96TDS900.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P82B96TD/S900
Manufacturer:
TI
Quantity:
2 898
NXP Semiconductors
7. Functional description
P82B96_8
Product data sheet
Refer to
The P82B96 has two identical buffers allowing buffering of both of the I
SCL) signals. Each buffer is made up of two logic signal paths, a forward path from the
I
buffered bus input to drive the I
The rest of this discussion will address only the ‘x’ side of the buffer; the ‘y’ side is
identical.
The I
The logic threshold voltage levels on the I
The maximum I
3 mA.
The logic level of Rx is determined from the power supply voltage V
LOW is below 42 % of V
threshold of half V
Tx is an open-collector output without ESD protection diodes to V
via a pull-up resistor to a supply voltage in excess of V
exceeded. It has a larger current sinking capability than a normal I
able to sink a static current of greater than 30 mA, and typical 100 mA dynamic pull-down
capability as well.
A logic LOW is only transmitted to Tx when the voltage at the I
0.6 V. A logic LOW at Rx will cause the I
accordance with I
enough to be looped back to the Tx output and cause the buffer to latch LOW.
The minimum LOW level this chip can achieve on the I
0.8 V.
If the supply voltage V
Their open-collector configuration allows them to be pulled up to the rated maximum of
15 V even without V
loading of external signals even when V
The effective input capacitance of any signal pin, measured by its effect on bus rise times,
is less than 7 pF for all bus voltages and supply voltages including V
Remark: Two or more Sx or Sy I/Os must not be interconnected. The P82B96 design
does not support this configuration. Bidirectional I
direction control pin so, instead, slightly different logic low voltage levels are used at Sx/Sy
to avoid latching of this buffer. A ‘regular I
will be propagated to Sx/Sy as a ‘buffered LOW’ with a slightly higher voltage level. If this
2
C-bus interface pin which drives the buffered bus, and a reverse signal path from the
•
•
sense the voltage state of the I
Tx (Ty respectively), and
sense the state of the pin Rx (Ry) and pull the I
LOW.
2
C-bus pin (Sx) is designed to interface with a normal I
Figure 1 “Block diagram of
2
C-bus supply voltage is 15 V and the guaranteed static sink current is
2
CC
C-bus requirements (maximum 1.5 V in 5 V applications) but not low
CC
).
Rev. 08 — 10 November 2009
CC
present. The input configuration on Sx and Rx also present no
CC
fails, then neither the I
, and logic HIGH is above 58 % of V
2
C-bus interface. Thus these paths are:
2
P82B96”.
C-bus pin Sx (or Sy) and transmit this state to the pin
CC
2
C-bus (Sx) to be pulled to a logic LOW level in
2
2
C-bus LOW’ applied at the Rx/Ry of a P82B96
C-bus are independent of the IC supply V
is not present.
2
C-bus nor the Tx output will be held LOW.
2
C-bus signals do not allow any
2
C-bus pin LOW whenever Rx (Ry) is
CC
2
C-bus by a LOW at Rx is typically
, as long as the 15 V rating is not
Dual bidirectional bus buffer
2
C-bus.
CC
2
C-bus pin (Sx) is below
CC
(with a typical switching
2
C-bus device, being
CC
. It may be connected
CC
of the chip. Logic
2
© NXP B.V. 2009. All rights reserved.
= 0 V.
C-bus (SDA and
P82B96
4 of 32
CC
.